Land Pride AFM4214 Transport Machinery Safely, Use a Safety Chain, Practice Safe Maintenance

Page 4

Table of Contents

Important Safety Information

Land Pride

These are common practices that may or may not be applicable to the products described in this manual.

Use Safety

Lights and Devices

Slow moving tractors, self- propelled equipment, and towed implements can create a hazard when driven on public roads. They are difficult to see, especially at night.

Flashing warning lights and turn signals are recommended whenever driving on public roads.

Transport

Machinery Safely

Comply with state and local laws.

Maximum transport speed for implement is 20 mph. DO NOT EXCEED. Never travel at a speed which does not allow adequate control of steering and stopping. Some rough terrain require a slower speed.

Sudden braking can cause a towed load to swerve and upset. Reduce speed if towed load is not equipped with brakes.

Use the following maximum speed - tow load weight ratios as a guideline:

20 mph when weight is less than or equal to the weight of tractor.

10 mph when weight is double the weight of tractor.

IMPORTANT: Do not tow a load that is more than double the weight of tractor.

Use A Safety Chain

A safety chain will help control drawn machinery should it separate from the tractor drawbar.

Use a chain with the strength rating equal to or greater than the gross weight of the towed machinery.

Attach the chain to the tractor drawbar support or other specified anchor location. Allow only enough slack in the chain to permit turning.

Do not use safety chain for towing.

Practice Safe

Maintenance

Understand procedure before doing work. Use proper tools and equipment, refer to Operator’s Manual for additional information.

Work in a clean dry area.

Lower the implement to the ground, put tractor in park, turn off engine, and remove key before

performing maintenance.

Allow implement to cool completely.

Do not grease or oil implement while it is in operation.

Inspect all parts. Make sure parts are in good condition & installed properly.

Remove buildup of grease, oil or debris.

Remove all tools and unused parts from implement before operation.

2

AFM4214 and AFM4216 All-Flex Grooming Mowers 315-587M

11/14/08

Image 4
Contents All-Flex Grooming Mowers Table of Contents Safety at All Times Practice Safe Maintenance Use a Safety ChainTransport Machinery Safely Tire Safety Wear Protective EquipmentAvoid High Pressure Fluids Hazard Keep Riders Off MachinerySafety Labels 818-339C818-019C 818-561C 818-560C818-337C 818-130C 818-351C 818-353C818-552C 818-556C818-045C 818-555C818-513C 818-003C818-543C 818-230C 818-229C818-335C 818-552C 818-540C Using This Manual ApplicationOwner Assistance IntroductionLand Pride Service Department East North Street Assembly and Set-up Tractor RequirementsTractor Hook-up Hardware Torque InformationMain Driveline Installation Check Constant Velocity Driveline LengthGauge Wheel Assembly Hydraulic Hook-upPull Rope Hook-up AFM4216 Model OnlyBleeding The Fold Hydraulics Table of Contents Constant Velocity Driveline Angle Pre-Operation InstructionsOperating Check List Constant Velocity ShaftOperating Instructions AFM4214 & AFM4216 ModelsGeneral Operating Instructions Adjustments Deck Height AdjustmentsCutting Height Chart Excessive Belt Tension May Lead to Belt TensionNot Enough Belt Tension May lead to Accessory Part Numbers AccessoriesBall Swivel Hitch Cutting BladesMaintenance Maintenance and LubricationServicing Mower Blades Blade InspectionLand PrideTable of Contents Blade Sharpening Belt Installation Blade OptionsDriveline Protection Clutch Disassembly, Inspection & AssemblyType a Clutches Clutch Run-In Plate Disassembly Step Plate Assembly StepDisassembly and Assembly Type B Clutch Clutch Run-InTires With Air Pressure StorageLand Pride Aerosol Touch-up Paint Lubrication Points HoursDriveline Constant Velocity Shaft Driveline ShaftsSeasonally Wheel Support BushingsWheel Bushings Gauge Wheels Wheel Bushings Transport HubsRequired Blade Spindle BearingsWay Gearbox Mower Deck GearboxTransport Locks Tool Bar to Deck Pivot PinWing Deck Pivot Bushings Rear Deck Pivot Half Clamps Wing Flex Pivot LugsSpecifications & Capacities Description Specification / CapacityAFM4214 Series 14044 AFM4216 Series 13665 Features Benefits Features & BenefitsAFM4214 & AFM4216 All-Flex Grooming Mower Troubleshooting Problem Cause Solution Discharge openings PluggedBelt slipping Patches of uncut grassTorque Values Chart Tire Inflation ChartAppendix Additional Torque ValuesTable of Contents Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA
Related manuals
Manual 88 pages 17.11 Kb