Table of Contents
Section 2: Operating Instructions
Land Pride
Refer to Figure 2-3:
3.AFM4216 models only. If narrow transport width is required or if transporting long distances:
a.Insert 5/8” deck float pin (#1) in lock hole located to the outside of both mower wing decks.
b.Make sure deck float pin is fully inserted.
26567 |
Model AFM4216 Deck Float Pin
Figure
NOTE: Be sure to remove deck floating pins before unfolding mower decks.
4.Refer to “Operating Instructions” on page 19 when lowering the decks.
Constant Velocity Driveline Angle
Refer to Figure 2-4:
•Grease driveline shaft and all other grease fittings.
•Check oil level in gearboxes. Refer to the Lubrication portion of the “Maintenance and Lubrication” section starting on page 24.
•Check all plugs and caps in gearboxes to make certain that they have been replaced and tightened properly.
•Check mower blades for sharpness and damage. See “Blade Inspection” on page 24.
•Be sure blades are installed properly on each deck with the cutting edge leading in rotation. See “Blade Removal And Installation” on page 25.
•Be sure all mower blade bolts are tight. Know which center blade bolts are left hand threaded and which are right hand threaded when checking for tightness. See “Blade Removal And Installation” on page 25.
•Be sure all bolts and nuts are tight.
•Be certain all guards and shields are in place and secure.
•Clear the area to be mowed of objects and debris that might be picked up and thrown by the mower blades
•Operate with 540 rpm PTO tractor.
•Refer to your tractor’s operator manual for engaging and disengaging the PTO.
•In case of emergency learn to stop tractor and mower quickly.
•Complete Operating Check List below.
The main driveline is equipped with a constant velocity (CV) joint that allows the unit to run at angles up to 80 degrees with no vibration.
19626 |
Constant Velocity Driveline Angle
Figure
IMPORTANT: Do not make turns that will subject the CV joint to angles greater than 80o. Angles greater than 80o will damage the driveline.
The constant velocity joint must be greased every 8 hours of operation. Refer to Page 31 “Driveline
Constant Velocity Shaft”.
Pre-Operation Instructions
Proper servicing and adjustments are key to the long life of any machine. With careful and systematic inspection of the mower, you can avoid costly maintenance, time and repair. Before beginning to operate your
Operating Check List
✔ | Check | Refer |
|
|
|
| Read and understand all Safety Rules. | Page 1 |
|
|
|
| Make sure all gearboxes are properly | Page 24 |
| lubricated. |
|
|
|
|
| Read and follow proper tractor | Page 13 |
| procedure. |
|
|
|
|
| Make sure all tires are properly inflated. | Page 43 |
|
|
|
| Lubricate mower components as needed. | Page 24 |
|
|
|
| Check mower initially and periodically for |
|
| loose bolts & pins. |
|
|
|
|
| Make sure hitch safety chain is securely | Page 13 |
| attached to the mower hitch and tractor. |
|
|
|
|
| Inspect cutting blades. Make note of blade | Page 24 |
| wear and sharpness. |
|
|
|
|
| Make a thorough examination of the |
|
| drivelines. Also check connections to the |
|
| gearboxes and tractor PTO shaft. |
|
|
|
|
| Make sure all guards and shields are in |
|
| place. |
|
|
|
|
18 | AFM4214 and AFM4216 | 11/14/08 |