Land Pride Parallel Arm Rotary Cutter, RCP2560, RCPM2560 manual Functional Check

Page 17

Land Pride

Table of Contents

Section 2: Assembly & Set-up

Functional Check

1.Remove the deck safety chain from the latch position and place the loose end on the stowage hook provided. See Figure 2-9.Start the tractor and adjust the 3-point hitch until the PTO shaft is approximately level.

2.Cycle the parallel arm and deck cylinders for proper operation.

!DANGER

Hydraulic fluid under pressure can penetrate skin. Wear protective gloves and safety glasses or goggles when working with hydraulic systems. Use a piece of cardboard or wood rather than hands when searching for hydraulic leaks. If hydraulic fluid is injected into the skin, it must be treated by a doctor within a few hours or gangrene may result.

NOTE: The following procedure assumes that the cutter is equipped with the optional Electric Cylinder Control. Go to step “c” if your cutter is not equipped with this option.

a.In Step 1.a. (Hydraulic Hookup), two hoses from the Solenoid Control Valve were connected to a single duplex outlet on the tractor. If the tractor is equipped with more than one remote duplex outlet, you must first determine which console lever is used to control this outlet. The control lever must then be locked into the “Automatic Extend Position” or the “Automatic Retract Position”.

b.Toggle the switch on the control box labeled “ARM1” by pushing it forward (away from you). The inboard parallel arm should extend outward. If it does not move, or moves in the opposite direction (retracts), you should either change the position of the console lever (from retract to extend or vice-versa) or reverse the hoses at the duplex outlet. Toggle the ARM1 switch by pulling back on it. The inboard parallel arm should retract. See Figure 2-10.

Repeat this procedure for the remaining arm and deck cylinders. Cycle all of the cylinders to full extension and retraction to remove any air that might be trapped in the system.

Check the hydraulic fluid level in your tractor's reservoir. If low, add fluid to the system before proceeding. The cylinders and hoses will require approximately 1 3/4 gallons from the tractor.

NOTE: The following procedure is for those cutters that are not equipped with the Electric Cylinder Control.

c.Operate the tractor console control lever designated for “ARM1” by pushing it forward. The inboard arm should extend outward. If the arm tries to retract, reverse the hoses at the duplex outlet. See Figure 2-10.

Repeat this procedure for the remaining arm and deck cylinders. Cycle all of the cylinders to full extension and retraction to purge any air that might be trapped in the system.

12254

Parallel Arm Movement

Figure 2-10

4/28/08

RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

15

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use Safety Lights and Devices Important Safety InformationUse a Safety Chain Practice Safe MaintenanceWear Protective Equipment Prepare for EmergenciesAvoid High Pressure Fluids Hazard Keep Riders Off Machinery818-230C 818-045C 818-339C818-229C 818-142C 818-390C 818-180C818-403C Used on 540 rpm PTO only 818-186C 818-391C818-003C 818-350C818-484C Used on 1000 rpm PTO only 818-338CApplication Using This ManualOwner Assistance IntroductionTractor Requirements Assembly & Set-upPoint Hookup Preparation ChecklistDealer Preparations Category Standard & Quick Hitch Standard Hitch Check Driveline Minimum Length PTO HookupHydraulic Hookup Electrical Hookup Functional Check Operator Protective Shield InstallationTiming Procedures Setting Flow Control ValveHydraulics Hydraulic Cylinder PlumbingMarking Hydraulic Line Lengths Breakaway Cylinder Installation Electric Cylinder Control Schematic Optional Adjustments Deck Level AdjustmentsTransporting Tension Bolt Operating ProceduresBreakaway Operations Breakaway Cylinder General Operating Instructions Hours Maintenance & LubricationLubrication Points Blade Servicing Replacement Storage Tractor MaintenanceTable of Contents RCP 2560 Parallel Arm Series Specifications & CapacitiesOverall Dimensions Problem Cause Solution TroubleshootingAdditional Torque Values Torque Values ChartAppendix Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.
Top Page Image Contents