Land Pride RCP2560, RCPM2560, Parallel Arm Rotary Cutter manual Blade Servicing Replacement

Page 30

Table of Contents

Section 7: Maintenance & Lubrication

Land Pride

The motor spindle hub housing (1), Figure 7-1has two cavity plugs located on one side of the housing just below the motor mounting flange. Position the cutter deck in the transport position and remove either plug to check fluid level. Fluid level should be within 1/2" of the top of the port. Add 80-90 weight gearlube as required. The capacity of the cavity is approximately 1/3 pint.

The speed increaser gearbox is mounted between the PTO shaft and the hydraulic pump. It increases the standard 540 RPM PTO speed to 2000 RPM at the pump. The oil should be changed after the first 100 working hours. Successive changes should be made after every 1500 hours or once a year. Use 80-90 weight gearlube. Check the oil level by removing the level plug located on the side of the case. Oil may be added by removing the breather located at the top of the case. A drain plug is located at the bottom of the case. See Figure 7-3.

13994

Motor/Spindle Hub

Figure 7-1

The hydraulic reservoir has an effective capacity of 35 gallons. A dipstick located on the filler cap indicates the correct reservoir fluid level.

A filter mounted on the hydraulic reservoir is used to clean the pump and motor system fluid. It should be replaced after 2 years of service. A conventional 10 micron filter element should be used See Figure 7-2.

12469

Filter Removal

Figure 7-2

12270

Speed Increaser

Figure 7-3

Blade Servicing (Replacement)

The cutter blades should be inspected on a daily basis. They must be kept sharp and should be replaced if they are worn excessively.

Both blades should be sharpened at the same angle as the original cutting edge and must be replaced or reground at the same time to maintain proper balance during rotation. Do not remove any more material than necessary when sharpening blades.

IMPORTANT: Replace blades with genuine Land Pride blades only. If one blade is to be replaced, the mating blade must also be replaced. Failure to do so will result in an out-of-balance condition that will contribute to premature bearing failure on the spindle hub. Factory blades are 4" wide and 25"

When replacing or sharpening the cutter blades, examine the blade bolts, shims and blade bolt nut. Replace if necessary. Be sure that the blades are installed properly. The airfoil (lift) must be oriented towards the top of the deck. The blade bolt nuts must be torqued to 450 ft-lbs.

28 RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Page 29 Page 31
Image 30
Page 29 Page 31
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use a Safety Chain Important Safety InformationUse Safety Lights and Devices Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-045C 818-339C 818-229C818-230C 818-180C 818-142C 818-390C818-391C 818-403C Used on 540 rpm PTO only 818-186C818-484C Used on 1000 rpm PTO only 818-350C818-003C 818-338COwner Assistance Using This ManualApplication IntroductionAssembly & Set-up Tractor RequirementsPreparation Checklist Dealer PreparationsPoint Hookup Category Standard & Quick Hitch Standard Hitch PTO Hookup Check Driveline Minimum LengthHydraulic Hookup Electrical Hookup Functional Check Installation Operator Protective ShieldSetting Flow Control Valve Timing ProceduresHydraulic Cylinder Plumbing HydraulicsMarking Hydraulic Line Lengths Breakaway Cylinder Installation Electric Cylinder Control Schematic Optional Deck Level Adjustments AdjustmentsTransporting Operating Procedures Breakaway OperationsTension Bolt Breakaway Cylinder General Operating Instructions Maintenance & Lubrication Lubrication PointsHours Blade Servicing Replacement Tractor Maintenance StorageTable of Contents Specifications & Capacities RCP 2560 Parallel Arm SeriesOverall Dimensions Troubleshooting Problem Cause SolutionTorque Values Chart AppendixAdditional Torque Values Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.
Top Page Image Contents