Land Pride Parallel Arm Rotary Cutter, RCP2560, RCPM2560 Tractor Requirements, Assembly & Set-up

Page 11

Land Pride

Table of Contents

Section 2: Assembly & Set-up

Tractor Requirements

The Parallel Arm Cutter, by design, must be used only on tractors that are capable of controlling the cutter under all operating conditions. When the arms are fully extended, a right-hand torque load on the tractor is present which will try to tip the tractor over! The tractor MUST have a minimum weight of 7000 lbs. A 3-Point Category II or Category III hitch with hydraulic lift control is required.

As shown in Figure 2-1,the rear wheel base must be not less than 74" wide as measured from the outside of each tire. If the right-hand tractor tire is more than 47" from the center of the tractor, it may interfere with the hydraulic motor on the deck when it is in the transport position. If the tractor is equipped with dual wheels, the right-hand dual may have to be removed.

12250

Minimum Tractor Requirements

Figure 2-1

A single, tractor duplex hydraulic outlet is required if the cutter is equipped with the optional Electric Cylinder Control. Three duplex hydraulic outlets will be needed for parallel arm and deck control if the cutter is NOT equipped with the optional Electric Cylinder Control.

An additional tractor, duplex hydraulic outlet is required if the cutter is equipped with the optional hydraulic breakaway cylinder.

Atractor Power Take-Off (PTO) is required for pump/ motor operation. This cutter is available with either 540 rpm or 1000 rpm rated PTO speed increasers. For best fuel economy, it is recommended that the 540 rpm unit be used on 1000 rpm tractors. However, PTO output RPM must be carefully controlled (by engine RPM) such that the PTO speed does not exceed 540 RPM. The actual horsepower required for pump/motor operation is approximately 30 HP.

If the tractor weight is less than 8500 lbs, auxiliary counterbalance weights will be required. These weights can be added to the weight bracket of the hydraulic reservoir or (preferably) to the left-hand tractor wheel.

The reservoir weight bracket is designed to be used with conventional John Deere type suitcase weights - each weight being 100 lbs. A total of 8 weights can be added to the bracket.

The tractor MUST be equipped with operator protective equipment in the form of shielding from thrown objects and Roll Over Protective Structure (ROPS) as shown in Figure 2-1.

A universal operator protective shield is available from Great Plains Mfg. Refer to page 16 for more information and installation.

It is also recommended that protective shielding or screen be added to the right hand side of the tractor engine cowling and radiator. This will help protect the tractor finish and radiator against thrown objects.

The lower 3-Point links of the 3-Point hitch must be stabilized to prevent side-to-side movement. Most tractors have sway blocks or adjustable chains for this purpose.

4/28/08

RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Practice Safe Maintenance Important Safety InformationUse Safety Lights and Devices Use a Safety ChainKeep Riders Off Machinery Prepare for EmergenciesWear Protective Equipment Avoid High Pressure Fluids Hazard818-230C 818-045C 818-339C818-229C 818-142C 818-390C 818-180C818-403C Used on 540 rpm PTO only 818-186C 818-391C818-338C 818-350C818-003C 818-484C Used on 1000 rpm PTO onlyIntroduction Using This ManualApplication Owner AssistanceTractor Requirements Assembly & Set-upPoint Hookup Preparation ChecklistDealer Preparations Category Standard & Quick Hitch Standard Hitch Check Driveline Minimum Length PTO HookupHydraulic Hookup Electrical Hookup Functional Check Operator Protective Shield InstallationTiming Procedures Setting Flow Control ValveHydraulics Hydraulic Cylinder PlumbingMarking Hydraulic Line Lengths Breakaway Cylinder Installation Electric Cylinder Control Schematic Optional Adjustments Deck Level AdjustmentsTransporting Tension Bolt Operating ProceduresBreakaway Operations Breakaway Cylinder General Operating Instructions Hours Maintenance & LubricationLubrication Points Blade Servicing Replacement Storage Tractor MaintenanceTable of Contents RCP 2560 Parallel Arm Series Specifications & CapacitiesOverall Dimensions Problem Cause Solution TroubleshootingAdditional Torque Values Torque Values ChartAppendix Overall Unit and Driveline One year Parts and Labor WarrantyCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.
Top Page Image Contents