Land Pride Parallel Arm Rotary Cutter Breakaway Operations, Tension Bolt, Operating Procedures

Page 26

Table of Contents

Section 6: Operating Procedures

! WARNING

! WARNING

Land Pride

The following operating procedures must be carefully read and fully understood. You are the tractor operator and are therefore responsible for the safe operation of this unit. All other persons must be cleared of the area. Cutter operation must be stopped when in the vicinity of other persons.

11.After attachment to the tractor, carefully raise and lower the cutter to ensure that the drawbar, tires, and other equipment on the tractor do not contact the cutter frame or PTO shaft.

12.Check all hoses and wires to be sure that they will not contact the PTO shaft. PTO guards must be in good condition and in place.

13.When the deck is in the transport position, and the PTO disengaged, check to be sure the blades are not locked (overlapped) together. The deck safety chain must be engaged in the deck hook provided.

14.Check blades for sharpness and ensure that both blade bolts as well as the center blade carrier hub nut are tight. Check tractor safety equipment - particularly the ROPS (Roll Over Protective Structure) and the operator safety screen to be sure both are in good working condition. Wear your safety glasses.

15.Remove and stow the deck safety chain just prior to cutting. Adjust lower 3-point links such that the PTO shaft is approximately level. Extend the cutters parallel arms out and position the deck flat on the ground.

16.Increase tractor throttle to approximately 500 RPM and slowly engage the PTO. Initial start-up vibration is normal, but should stop after a few revolutions of the blade carrier. If vibration continues, stop PTO rotation. Wait for the blade carrier to come to a complete stop before dismounting from the tractor, then check the blades to be sure they are not locked together.

17.Once the cutter is running smooth increase tractor throttle to provide for 540 PTO RPM.

IMPORTANT: If a 1000 RPM tractor PTO is being used, engine RPM MUST be reduced to limit PTO RPM to 540. Excessive engine speed will cause damage to the speed increaser and other power train components.

18.Position the cutter deck for best operator visibility. This is normally with the arms extended to approximately 3/4 of full extension. Adjust deck attitude and height. Optimum ground speed will depend on the density of the material being cut, operator awareness, and (in some cases) terrain. If in doubt, reduce tractor ground speed to a comfortable level.

Do not operate this cutter under any terrain conditions that would place the tractor at an angle exceeding 30 degrees either front-to-rear or left-to-right. Ensure that adequate ballast weights are provided on both the front of the tractor and left of the tractor and left hand side of cutter to assure tractor stability. See Figure 6-1.

!WARNING

30° MAX

ROLL OVER HAZARD

TO AVOID SERIOUS INJURY OR DEATH

•THIS CUTTER MUST NOT BE ATTACHED TO TRACTORS THAT

WEIGH LESS THAN 7000 LBS OR HAVE A WHEELBASE LESS THAN 74" WIDE. AUXILIARY WEIGHTS MAY BE REQUIRED. CONSULT YOUR OWNERS MANUAL FOR DETAILS.

•EQUIP TRACTOR WITH APPROVED ROPS (ROLL OVER PROTECTION STRUCTURE). CONSULT YOUR OWNERS MANUAL FOR SPECIFICS.

818-391C

Maximum Tractor Angle

Figure 6-1

Breakaway Operations

This cutter is designed for breakaway of the cutter head and parallel arms in the event the cutter head contacts an immovable object or irregular terrain during forward tractor movement. The “breakaway” will prevent structural damage to the cutter head, parallel arms, and mainframe in the event of such contact. See Figure 6-2.

Upon breakaway, the cutter head must be reset to the original "home" position before normal cutting operations can be resumed. Reset to the home position is accomplished somewhat differently depending on whether the cutter is equipped with the standard tension bolt or the optional breakaway (hydraulic) cylinder.

Tension Bolt

1.Raise the arms and deck upward to clear any obstacles located behind the cutter deck.

2.Slowly back the tractor and cutter away from those obstacles that would interfere with rotating the deck and arms back to the “home” position.

!WARNING

Shut off PTO power, put the tractor in park and wait for the blades to stop rotating before dismounting from the tractor.

24 RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Image 26
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use a Safety Chain Important Safety InformationUse Safety Lights and Devices Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-230C 818-045C 818-339C818-229C 818-180C 818-142C 818-390C818-391C 818-403C Used on 540 rpm PTO only 818-186C818-484C Used on 1000 rpm PTO only 818-350C818-003C 818-338COwner Assistance Using This ManualApplication IntroductionAssembly & Set-up Tractor RequirementsPoint Hookup Preparation ChecklistDealer Preparations Category Standard & Quick Hitch Standard Hitch PTO Hookup Check Driveline Minimum LengthHydraulic Hookup Electrical Hookup Functional Check Installation Operator Protective ShieldSetting Flow Control Valve Timing ProceduresHydraulic Cylinder Plumbing HydraulicsMarking Hydraulic Line Lengths Breakaway Cylinder Installation Electric Cylinder Control Schematic Optional Deck Level Adjustments AdjustmentsTransporting Tension Bolt Operating ProceduresBreakaway Operations Breakaway Cylinder General Operating Instructions Hours Maintenance & LubricationLubrication Points Blade Servicing Replacement Tractor Maintenance StorageTable of Contents Specifications & Capacities RCP 2560 Parallel Arm SeriesOverall Dimensions Troubleshooting Problem Cause SolutionAdditional Torque Values Torque Values ChartAppendix Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.