Land Pride RCP2560, RCPM2560, Parallel Arm Rotary Cutter Operator Protective Shield, Installation

Page 18

Table of Contents

Section 2: Assembly & Set-up

Land Pride

Check the hydraulic fluid level in your tractor's reservoir. If low, add fluid to the system before proceeding. The cylinders and hoses will require approximately 1 3/4 gallons from the tractor.

d.Move the tractor and cutter to a remote location (away from all other persons) to check pump/ motor operation. Check to be sure the Hydraulic Reservoir shut-off valve is full OPEN. If this service valve is turned off, damage will occur to the pump.

Position the cutter deck flat on the ground or concrete surface. SLOWLY engage the PTO to start blade rotation. On initial start-up, blade position may cause the deck to “vibrate”. After 2- 3 revolutions, these vibrations should stop. If the deck continues to vibrate, shut off the PTO, raise the deck and check for locked blades.

Gradually increase engine RPM until PTO output RPM is 540. The deck should not exhibit excessive vibration.

IMPORTANT: If the tractor being used is equipped with a 1000 RPM PTO output, be sure that throttle RPM is reduced to limit PTO output to 540 RPM.

Operator Protective Shield

An optional operator protective shield is available for use on tractors not equipped with cabs or other protective shielding. This shield is a "universal" type and is suitable for attachment to a conventional Roll Over Protective Structure (ROPS) bar that is already attached to the tractor. The shield is constructed of an extruded aluminum frame and is glazed with 1/4" clear, lexan polycarbonate.

Mounting hardware will permit attachment to ROPS having cross-section dimensions of 2" x 4", 2" x 5", and 2" x 6" or 2 1/2" x 4", 2 1/2" x 5 and 2 1/2" x 6. Other sizes may require longer mounting bolts and/or custom flatbars. Installation requires that 4 mounting holes be drilled in the frame of the shield. No modification is made to the ROPS.

Installation

Refer to Figure 2-11:

Measure the width and thickness of the ROPS bar on the tractor to determine that the clamping hardware supplied will be adequate.

Compare the parts list on and quantities with the parts received. Report any missing or damaged items to your dealer.

To determine the best location for the shield, the cutter should be connected to the tractor. The parallel arms should be fully extended and the deck should be horizontal (or approximately level).

Carefully remove the shield from the shipping carton and temporarily position it on the inside surface of the ROPS bar. Locate the shield forward/back, up/down to provide the best overall coverage for the tractor operator. Use a spirit level to level the shield before marking. Mark the top frame location with a pencil on each side of the ROPS bar, and mark the vertical ROPS location on the frame of the shield.

Position the shield (#5) on a flat work surface. Locate one of the 316-116D (#4) flatbars next to the pencil marks to determine which set of holes will clear the vertical marks for the ROPS location. Mark the hole location and drill two 1/4" diameter holes through the frame of the shield. Similarly mark and drill two additional holes for the lower clamp location.

Attach the shield to the inside surface of the ROPS bar using the mounting hardware provided (#1), (#2), (#3), and (#6).

13239

Operator Protective Shield

Figure 2-11

16 RCP2560 & RCPM2560 Series Parallel Arm Rotary Cutter 316-057M

4/28/08

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Parallel Arm Rotary Cutter Table of Contents Safety at All Times Use a Safety Chain Important Safety InformationUse Safety Lights and Devices Practice Safe MaintenanceAvoid High Pressure Fluids Hazard Prepare for EmergenciesWear Protective Equipment Keep Riders Off Machinery818-045C 818-339C 818-229C818-230C 818-180C 818-142C 818-390C818-391C 818-403C Used on 540 rpm PTO only 818-186C818-484C Used on 1000 rpm PTO only 818-350C818-003C 818-338COwner Assistance Using This ManualApplication IntroductionAssembly & Set-up Tractor RequirementsPreparation Checklist Dealer PreparationsPoint Hookup Category Standard & Quick Hitch Standard Hitch PTO Hookup Check Driveline Minimum LengthHydraulic Hookup Electrical Hookup Functional Check Installation Operator Protective ShieldSetting Flow Control Valve Timing ProceduresHydraulic Cylinder Plumbing HydraulicsMarking Hydraulic Line Lengths Breakaway Cylinder Installation Electric Cylinder Control Schematic Optional Deck Level Adjustments AdjustmentsTransporting Operating Procedures Breakaway OperationsTension Bolt Breakaway Cylinder General Operating Instructions Maintenance & Lubrication Lubrication PointsHours Blade Servicing Replacement Tractor Maintenance StorageTable of Contents Specifications & Capacities RCP 2560 Parallel Arm SeriesOverall Dimensions Troubleshooting Problem Cause SolutionTorque Values Chart AppendixAdditional Torque Values Warranty Overall Unit and Driveline One year Parts and LaborCorporate Office P.O. Box Salina, Kansas 67402-5060 USA

Parallel Arm Rotary Cutter, RCPM2560, RCP2560 specifications

The Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters represent a significant advancement in agricultural and landscaping equipment, designed to efficiently tackle a variety of mowing tasks. These rotary cutters are ideal for maintaining pastures, roadsides, and large fields while offering enhanced durability and performance.

One of the main features of the RCP2560 and RCPM2560 is their robust construction. Built with a heavy-duty frame and steel components, these cutters are engineered to withstand the rigors of tough mowing conditions. They feature a fully welded deck to ensure strength and longevity, providing operators with confidence during operation.

A key characteristic of the Parallel Arm design is the ability to deliver consistent cutting performance across varying terrains. This unique design allows the cutter to follow the ground contour closely, ensuring that the blades maintain an even cutting height. This is especially beneficial when navigating uneven or hilly landscapes, delivering a professional-quality finish.

The RCP2560 and RCPM2560 come equipped with high-capacity cutter blades designed for efficient grass and brush cutting. These blades are strategically angled to optimize cutting efficiency while minimizing power consumption. Users can enjoy reduced maintenance costs and longer service intervals because of the durable, replaceable blades.

The technology behind these rotary cutters includes a quick-attach mounting system, making it easier for operators to connect and disconnect the mower from their tractors. This feature saves time and enhances productivity, allowing for quicker transitions between tasks.

Additionally, the RCPM2560 model offers a medium-duty option, catering to operators looking for versatility in their cutting operations. Both models come with adjustable side skids that enable operators to modify the cutting height easily, further enhancing their adaptability for different mowing applications.

Safety is paramount with Land Pride's rotary cutters, which are designed with user-friendly controls and a stable operating design. Optional safety features, such as a chain guard, are available to protect against flying debris, underscoring the focus on operator safety.

In summary, the Land Pride RCP2560 and RCPM2560 Parallel Arm Rotary Cutters bring together durability, efficiency, and user-friendly features to transform landscaping and agricultural mowing tasks. With their advanced technologies and robust construction, these rotary cutters are a valuable investment for any operator looking to achieve superior cutting performance.
Top Page Image Contents