Kohler 12RESM1 manual Prestart Installation Check, Startup Notification

Page 27

 

1

 

3

 

 

12 kW Carburetor Heater

 

 

 

 

GM19463

 

1

2

3

 

 

 

GM57968

 

 

17/18 kW Carburetor Heater

 

1.

Thermostat

 

 

2.

Connector

 

 

3.

Heater

 

 

Figure 1-26 Carburetor Heaters

1.11 Prestart Installation Check

Review the entire installation section. Inspect all wiring and connections to verify that the generator set is ready for operation. Check all items in the following Prestart Checklist.

Prestart Checklist

Air Cleaner. Check that a clean air cleaner element is installed to prevent unfiltered air from entering the engine. See the generator set Operation Manual for instructions.

Air Inlets. Check for clean and unobstructed air inlets.

Battery. Check for tight battery connections. Consult the battery manufacturer’s instructions regarding battery care and maintenance.

Exhaust System. Check for exhaust leaks and blockages. Check the muffler condition.

DInspect the exhaust system components for cracks, leaks, and corrosion. Check for tight exhaust system connections.

DCheck for corroded or broken metal parts and replace them as needed.

Oil Level. Maintain the oil level at or near, not over, the full mark on the dipstick.

Operating Area. Check for obstructions that could block the flow of cooling air. Keep the air intake area clean. Do not leave rags, tools, or debris on or near the generator set.

1.12 Startup Notification

Complete the startup and installation checklists supplied with the startup notification form. Complete and sign the startup notification form and return copies to Kohler Co. and the distributor/dealer as instructed on the form.

Standby systems not registered within 60 days of startup are automatically registered using the manufacturer’s ship date as the startup date.

DCheck that the exhaust outlet is unobstructed.

TP-6516 4/09

Section 1 Installation 27

Image 27
Contents Models Controller DC-RET Digital ControlTP-6516 4/09d Controller Identification Product Identification InformationGenerator Set Identification Numbers Engine IdentificationTable of Contents TP-6516 4/09 Safety Precautions and Instructions BatteryAccidental Starting Engine Backfire/Flash Fire Exhaust SystemFuel System Hazardous Noise Hazardous Voltage/ Moving PartsHeavy Equipment Hot Parts Detail IntroductionGenerator Set Component Locations, 17/18 kW Models Service Assistance TP-6516 4/09 Generator Set Inspection InstallationGeneral LiftingSee Section Generator Set Clearances, 12 kW Models, ADV-7466, Sheet Installation TP-6516 4/09 Generator Set Clearances, 17/18 kW Models, ADV-7341-B, Sheet Power Supply Exhaust RequirementsAir Requirements Fuel Supply Fuel RequirementsFuel Conversion Fuel Pipe SizeFuel Conversion 17 Dsai Connection AC Connections Electrical ConnectionsBattery Charger Remote Start ConnectionGrounding EZ-273000-J Engine starting battery location 24 Carburetor Heater, 17/18 kW Carburetor Heater optionalStartup Notification Prestart Installation CheckInstallation TP-6516 4/09 Wiring Diagrams and Schematics Wiring DiagramsSchematic Diagram, 12 kW Models, ADV-7351 Point-to-Point Wiring Diagram, 12 kW Models, GM52471 Schematic Diagram, Single Phase, 17/18 kW Models, ADV-7353 TP-6516 4/09 Wiring Diagrams Wiring Diagrams TP-6516 4/09 Ansi Appendix a AbbreviationsLCB TP-6516 4/09 TP-6516 4/09 Page 2007, 2008, 2009 by Kohler Co. All rights reserved