Jonsered BC2145, FC2145W manual Fitting other guards and cutting attachments

Page 15

ASSEMBLY

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

•Place the blade (D) and support flange (F) on the output shaft.

G

F

 

D

B

C

•Fit the nut (G). The nut must be tightened to a torque of 35-50 Nm (3.5-5 kpm). Use the socket spanner in the tool kit. Hold the shaft of the spanner as close to the blade guard as possible.

To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (Caution! left-hand thread).

When loosening and tightening the saw blade nut, there is a risk of injury from the teeth of the saw blade. You should therefore always ensure that your hand is shielded by the blade guard when doing this. Always use a socket spanner with a shaft that is long enough to allow this. The arrow in the diagram shows the area where you should operate the socket spanner when loosening or tightening the nut.

Fitting the trimmer guard and trimmer head Trimmy SII

•Fit the correct trimmer guard (A) for use with the trimmer head. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

•Fit the drive disc (B) on the output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

H

L P

BA M C

M LA

•Insert the locking pin (C) in the hole to lock the shaft.

•Screw on the trimmer head (H) in the opposite direction to the direction of rotation.

H

C

•Tighten the trimmer head to a torque of 35-50 Nm (3.5-5 kpm).

•To dismantle, follow the instructions in the reverse order.

Fitting other guards and cutting attachments

Fit the trimmer guard/combination guard (A) intended for use with the trimmer head/plastic blades. Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

H

P

BA

ML

•Fit the drive disc (B) on the output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

L

M C

A

•Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation.

•To dismantle, follow the instructions in the reverse order.

English – 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Operator’s manual EPA KEY to Symbols SymbolsCome closer than 15 metres Contents Dear customer IntroductionWhat is what on the clearing saw? BC What is WHAT?Decompression valve FC 2145 S, FC 2145 W Personal protective equipment General Safety PrecautionsMachine′s safety equipment Stop switchThrottle lock Muffler Cutting attachment guardVibration damping system Quick releaseCutting equipment Locking nutLocking screw General rules Cutting equipmentSharpening grass cutters and grass blades Sharpening the saw bladeTrimmer head FC 2145, FC 2145 S, FC 2145 W AssemblyAssembling the handlebar and throttle Transport position, handlebarFitting the blade guard and saw blade Assembling the cutting equipmentFitting the trimmer guard and trimmer head Trimmy SII Fitting other guards and cutting attachmentsAdjusting the harness and clearing saw Standard harnessVector harness Correct balance Fuel safety Fuel HandlingFuel Mixing FuelingCold engine Starting and StoppingCheck before starting Starting and stoppingStarting StoppingHeated handles ABC of clearing Basic safety rulesWorking Techniques General working instructionsWorking methods Forestry clearing using a saw bladeTrimming Grass clearing using a grass bladeBrush cutting with a saw blade Grass trimming with a trimmer headClearing CuttingSweeping Carburetor MaintenanceSetting procedure with a load Trimmer head should be used Fine adjustment of the idle speed TCorrectly adjusted carburetor Setting procedure without a load Blade can be usedProceed as follows Adjusting the start throttle speed BCMuffler Cooling systemSpark plug Air filterBevel gear Drive shaftWinter use Temperature 0C 32F or colderMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Federal Emission Control Warranty StatementPoly Trim Clic 35-50 NM 095-.130Page Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1150102-95 ´z+R*=¶5`¨ ´z+R*=¶5`¨
Top Page Image Contents