Jonsered BC2145, FC2145W manual Approved accessories Type Cutting attachment guard, Art. no

Page 33

TECHNICAL DATA

	BC 2145

	Approved accessories	Type	Cutting attachment guard, Art. no.

	Centre hole in blades/cutters, Ø 25,4 mm	Output shaft thread M12

		Multi 255-3 (Ø 255 3 teeth)	537 28 85-02

	Grass blade/grass cutter	Multi 275-4 (Ø 275 4 teeth)	537 28 85-02

		Multi 300-3 (Ø 300 3 teeth)	537 28 85-02

	Saw blade	Opti XS 200-22 (Ø 200 22 teeth)	537 31 09-01

		Scarlet 200-22 (Ø 200 22 teeth)	537 31 09-01
		Scarlet 200-22 (Ø 200 22 teeth)	537 31 09-01

	Plastic blades	Polytrim Ø 300	537 28 85-02

		Trimmy S II	503 95 43-04

	Trimmer head	Auto 55	503 95 43-04

		Tap n’Go 45	503 95 43-04

	Support cup	Fixed

		With ball bearing
		With ball bearing


	FC 2145, FC 2145 S, FC 2145 W

	Approved accessories	Type	Cutting attachment guard, Art. no.

	Centre hole in blades/cutters, Ø 20 mm	Output shaft thread M12

		Multi 255-3 (Ø 255 3 teeth)	537 29 74-02

	Grass blade/grass cutter	Multi 275-4 (Ø 275 4 teeth)	537 29 74-02

		Multi 300-3 (Ø 300 3 teeth)	537 29 74-02

		Opti XS 200-22 (Ø 200 22 teeth)	537 21 71-01

	Saw blade	Opti XS 225-24 (Ø 225 24 teeth)	502 03 94-06

		Scarlet 200-22 (Ø 200 22 teeth)	537 21 71-01
		Scarlet 200-22 (Ø 200 22 teeth)	537 21 71-01

		Scarlet 225-24 (Ø 225 24 teeth)	502 03 94-06

	Plastic blades	Polytrim Ø 300	537 29 74-02

		Trimmy S II	537 29 73-02

	Trimmer head	Auto 55	537 29 73-02

		Tap n’Go 45	537 29 73-02

	Support cup	Fixed

		With ball bearing
		With ball bearing

English – 33

Image 33

Contents Operator’s manual EPA KEY to Symbols SymbolsCome closer than 15 metres Contents Dear customer IntroductionWhat is what on the clearing saw? BC What is WHAT?Decompression valve FC 2145 S, FC 2145 W Personal protective equipment General Safety PrecautionsMachine′s safety equipment Stop switchThrottle lock Vibration damping system Cutting attachment guardQuick release MufﬂerCutting equipment Locking nutLocking screw Sharpening grass cutters and grass blades Cutting equipmentSharpening the saw blade General rulesTrimmer head Assembling the handlebar and throttle AssemblyTransport position, handlebar FC 2145, FC 2145 S, FC 2145 WFitting the blade guard and saw blade Assembling the cutting equipmentFitting the trimmer guard and trimmer head Trimmy SII Fitting other guards and cutting attachmentsAdjusting the harness and clearing saw Standard harnessVector harness Correct balance Fuel safety Fuel HandlingFuel Mixing FuelingCheck before starting Starting and StoppingStarting and stopping Cold engineStarting StoppingHeated handles Working Techniques Basic safety rulesGeneral working instructions ABC of clearingWorking methods Forestry clearing using a saw bladeBrush cutting with a saw blade Grass clearing using a grass bladeGrass trimming with a trimmer head TrimmingClearing CuttingSweeping Carburetor MaintenanceCorrectly adjusted carburetor Fine adjustment of the idle speed TSetting procedure without a load Blade can be used Setting procedure with a load Trimmer head should be usedMufﬂer Adjusting the start throttle speed BCCooling system Proceed as followsBevel gear Air ﬁlterDrive shaft Spark plugWinter use Temperature 0C 32F or colderMaintenance Daily Weekly Monthly Maintenance scheduleTechnical data Technical DataApproved accessories Type Cutting attachment guard, Art. no Your Warranty Rights and Obligations Federal Emission Control Warranty StatementPoly Trim Clic 35-50 NM 095-.130Page Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1150102-95 ´z+R*=¶5`¨ ´z+R*=¶5`¨