Jonsered FC2145W, BC2145 Assembling the cutting equipment, Fitting the blade guard and saw blade

Page 14

ASSEMBLY

Assembling the cutting equipment

WARNING! When fitting the cutting

!

attachment it is extremely important that the

raised section on the drive disc/support

•Position the blade (D) with the drive disk (B). Make sure that the blade is centered by fitting it to the guide on the drive disk.

•Fit the support flange (F) on the output shaft so that it rests against the blade.

flange engages correctly in the centre hole

of the cutting attachment. If the cutting

attachment is fitted incorrectly it can result

in serious and/or fatal personal injury.

N

F

E

WARNING! Never use a cutting attachment

!without an approved guard. See the chapter on Technical data. If an incorrect or faulty guard is fitted this can cause serious personal injury.

IMPORTANT! If a saw blade or grass blade are to be used the machine must be equipped with the correct handlebar, blade guard and harness.

Fitting the blade guard/combination guard, grass blade and ball-bearing- mounted support cup

•Hang the trimmer guard/combination guard (A) on the two hooks on the plate holder (M). Bend the guard around the shaft and tighten it with the bolt (L) on the opposite side of the shaft. Use the locking pin (C). Place the locking pin in the groove on the screw head and tighten. See diagram.

L

M C

A

•CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

•Fit the drive disc (B) on the angle gear’s output shaft.

•Centre the metal cup (P) on the drive disc’s blade guide.

•Turn the output shaft until one of the holes in the drive disk aligns with the corresponding hole in the gear housing.

•Insert the locking pin (C) in the hole to lock the shaft.

D

P

BA

C

ML

•Screw the support cup (E) onto the output shaft threads (CAUTION! Left-hand thread). Tighten to a torque of 35- 50 Nm (3.5-5.0 kpm). Use the socket spanner in the tool kit. Note that the locking pin (C) must remain inside the gear housing to lock the drive disk. Hold the shaft of the socket spanner as close to the blade guard/combination guard as possible.

WARNING! Tighten the lock screw (N) in the

!center hole of the support cup. Tighten to a torque of 35-50 Nm (3.5-5.0 kpm), CAUTION! Left-hand thread. If the lock screw is not fitted in the support cup, there is a risk that the support cup will come unscrewed. This means that the blade will also come loose, which could result in serious or fatal injury to the operator or others.

Fitting the blade guard and saw blade

•The blade guard (A) is fitted using 4 screws (L) as shown.

L

A

CAUTION! Always use the recommended guard for the cutting attachment you are using. See chapter on Technical data.

•Fit the drive disc (B) on the output shaft.

14 – English

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Operator’s manual EPA Come closer than 15 metres KEY to SymbolsSymbols Contents Introduction Dear customerWhat is WHAT? What is what on the clearing saw? BCDecompression valve FC 2145 S, FC 2145 W General Safety Precautions Personal protective equipmentThrottle lock Machine′s safety equipmentStop switch Quick release Cutting attachment guardVibration damping system MufflerLocking screw Cutting equipmentLocking nut Sharpening the saw blade Cutting equipmentSharpening grass cutters and grass blades General rulesTrimmer head Transport position, handlebar AssemblyAssembling the handlebar and throttle FC 2145, FC 2145 S, FC 2145 WAssembling the cutting equipment Fitting the blade guard and saw bladeFitting other guards and cutting attachments Fitting the trimmer guard and trimmer head Trimmy SIIVector harness Adjusting the harness and clearing sawStandard harness Correct balance Fuel Fuel safetyFuel Handling Fueling MixingStarting and stopping Starting and StoppingCheck before starting Cold engineHeated handles StartingStopping General working instructions Basic safety rulesWorking Techniques ABC of clearingForestry clearing using a saw blade Working methodsGrass trimming with a trimmer head Grass clearing using a grass bladeBrush cutting with a saw blade TrimmingSweeping ClearingCutting Maintenance CarburetorSetting procedure without a load Blade can be used Fine adjustment of the idle speed TCorrectly adjusted carburetor Setting procedure with a load Trimmer head should be usedCooling system Adjusting the start throttle speed BCMuffler Proceed as followsDrive shaft Air filterBevel gear Spark plugTemperature 0C 32F or colder Winter useMaintenance schedule Maintenance Daily Weekly MonthlyTechnical Data Technical dataApproved accessories Type Cutting attachment guard, Art. no Federal Emission Control Warranty Statement Your Warranty Rights and ObligationsPoly Trim 095-.130 Clic 35-50 NMPage Mm 9,0 m Mm 7,5 m Mm 6,0 m 15 cm 10 m 10 cm 15 cm Clic 1150102-95 ´z+R*=¶5`¨ ´z+R*=¶5`¨
Top Page Image Contents