Marantz R3001 manual Remote Control Operation, Function and Operation, AUDIO/VIDEO Input

REMOTE CONTROL

OPERATION

FUNCTION AND OPERATION

The provided remote control unit is a universal remote controller. The POWER button, numeric buttons and control buttons are used in common across different input source components.

The input source controlled with the remote control unit changes when one of the input selector but- tons is pressed.

	POWER				z
					x
	TV	VCR1	DSS/VCR2	DVD
	TUNER	CD	TAPE	CDR/MD	c
¤5		AUX1	AMP		v
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
¤4					b
¤3	OSD		MENU		n
		ENTER			m
¤2	SET UP/		MENU OFF		,
¤1	T.TONE
	PURE DIRECT	AUTO		DTS
¤0		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL	.
⁄9		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN	⁄0
⁄8		7	8	9
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
⁄7			0		⁄1
			CHANNEL/SKIP
⁄6	BASS	TREBLE	TUNE/SEARCH
⁄5		T-MODE RDS F.DIRECT			⁄2
⁄4	INPUT/DISC+	AUDIO	SUB-T/ATT	PTY
	CH.SEL			LIP.SYNC	⁄3

SYSTEM REMOTE CONTROLLER

RC5500SR

zTransmitting indicator

Lights up during a button is pressed and an infra- red signal is sending.

x(Main) POWER buttons

(when AMP mode is selected)

Press to switch the power of the SR3001 ON or OFF after pressing the AMP button.

cInput selector buttons/ FUNCTION SELECTOR buttons

(AUDIO/VIDEO INPUT)

These buttons are used to select a Audio or Video source component. Press one of these buttons once to change the function of the remote control. Press same button within 2 seconds, the input function of the SR3001 is changed.

Audio function sources such as CD, TAPE, CDR/MD, and TUNER may be selected in conjunction with a Video source.

This feature (Sound Injection) combines a sound from one source with a picture from another. Choose the video source first, and then choose a different audio source to activate this function.

Notes:

•CDR/MD button is set CDR function at initial. To switch MD function, press and hold down CDR/ MD button and press 2 button.

•To return CDR function, press and hold down CDR/ MD button and press 1 button.

v MAIN VOLUME UP (3) /DOWN (4)

buttons

Main volume control of the SR3001. The front, surround, center and subwoofer channel volumes controlled by these buttons simultaneously.

bMUTE button

Muting button of the SR3001. Press this button decrease the sound temporarily. Press this button again to return to the previous sound.

When this button is pressed, “MUTE” indicator lights up.

nMENU button

(when AMP mode is selected)

This button is used to enter the SETUP MAIN MENU.

mCursor (1, 2, 3, 4) / OK buttons

(when AMP mode is selected)

Use these button when operating the SETUP MAIN MENU.

,MENU OFF button

(when AMP mode is selected)

This button is used to exit from the SETUP MAIN MENU.

.Numeric buttons 1 to 9 / Surround mode buttons

Numeric buttons

These buttons are used to enter figures in the se- lection of a tuner preset station and station name preset or to set select a CD track number, etc. The functions of these buttons are dependent on the function button selected.

Surround mode buttons (when AMP mode is selected)

These buttons are used to select the surround mode.

⁄0 P.SCAN (Preset scan) / V(Video)-

OFF button

(when TUNER mode is selected)

This button is used to start preset scan when SR3001 is selected TUNER mode.

(when AMP mode is selected)

This is used when switching the video signals from the various monitor outputs to Video-Off mode.

⁄1 0 / A/D button

0 button

This button is used to enter the number “0”

A/D button (when AMP mode is selected)

This is used to switch between the analog and digital inputs.

⁄2 CONTROL buttons

These buttons are used when operating the CD player, TAPE deck, etc.

The function of these buttons are dependent on the function button selected.

For the controllable functions of each input function, please refer to controllable function table on the page 10.

⁄3 SUB-T (Title) / ATT (attenuator) button

When the input signal is too high and the voice distorts even while adjusting the SR3001 VOLUME control, turn on this function. “ATT” is illuminated when this function is activated.

The input level is reduced. Attenuator is invalid for the output signal of “REC OUT”.

Note:

This function is unavailable while the digital input is selected.

⁄4 INPUT/DISC+ / CH.SEL buttons

This button is used to enter the input level setup menu.

⁄5 TREBLE UP (3) /DOWN (4) buttons

These buttons are used to adjust the tone control of high frequency sound for left and right speaker.

⁄6 BASS UP (3) /DOWN (4) buttons

These buttons are used to adjust the tone control of low frequency sound for left, right and subwoofer speaker.

⁄7 MEMO button

Memory enable button for various preset functions.

⁄8 CLEAR button

This button is used to cancel for certain memory or programming operations.

⁄9 DISPLAY button

Selects the display mode for the front display of the SR3001.

¤0 NIGHT button

Pressing this button prevents the Dolby Digital signal from playback at a loud voice. This function reduces the voice by 1/3 to 1/4 at maximum. Thus, it eliminates the occurrence of an abruptly loud voice at night. However, the function is valid only in the case when the Dolby Digital signal is entered into OPTICAL or COAXIAL and data to compress the voice exists in the signal to be played back.

When this button is pressed, the “NIGHT” indicator is illuminated.

ENGLISH

7