Marantz R3001 manual Programming the Remote Controller, Programming with the 4-DIGIT Code

ENGLISH

¤1 PURE DIRECT button

When this button is pressed, the tone control circuit is bypassed.

¤2 SETUP / T.TONE button

(when AMP mode is selected)

Used to enter the test tone menu.

¤3 OSD button

Note:

This button is unavailable for SR3001.

¤4 SLEEP (sleep timer) button

This button is used for setting the sleep timer. It can be operated the same way as the button on the unit.

¤5 TV VOLUME UP (3) /DOWN (4) buttons

These buttons increase or decrease TV’s volume.

PROGRAMMING THE REMOTE CONTROLLER

The remote controller RC5500SR must be programmed to use the codes for your appliances of different brands. This is done by keying in a 4-digit code or by scanning the codes until the correct one is found. We recommend to using the 4-digit code. This mode is faster and more reliable. The code scanning method should be used only if you cannot find the code for one of your appliances. The codes are listed at the end of this book.

Important:

•Use the remote control buttons for programming, not the buttons of the receiver or other appliances.

•Some codes may be not match your equipment. In this case, your equipment cannot be controlled with this remote controller.

PROGRAMMING WITH THE 4-DIGIT CODE

							ENTER
					1.	SET UP/		MENU OFF
	POWER					T.TONE
						PURE DIRECT	AUTO		DTS
							1	2	3
						NIGHT	CSII	EX/ES	VIRTUAL
	TV	VCR1	DSS/VCR2	DVD			4	5	6
1.						DISPLAY	MCH-ST	STEREO	7.1CH IN
	TUNER	CD	TAPE	CDR/MD			7	8	9
						CLEAR	MEMO	A/D	P.SCAN/V-OFF
					2.			0
		AUX1	AMP					CHANNEL/SKIP
	TV			MAIN		BASS	TREBLE	TUNE/SEARCH
	VOL.	SLEEP	MUTE	VOL.
							T-MODE	RDS	F.DIRECT
	OSD		MENU

SCANNING THE CODE TABLE

4. POWER ENTER

					2.	SET UP/		MENU OFF
2.	TV	VCR1	DSS/VCR2	DVD		T.TONE
						PURE DIRECT	AUTO	5	DTS
					6.		4		6
							1	2	3
	TUNER	CD	TAPE	CDR/MD		NIGHT	CSII	EX/ES	VIRTUAL
4.		AUX1	AMP			DISPLAY	7	8	9
							MCH-ST	STEREO	7.1CH IN

TV			MAIN	3.	CLEAR	MEMO	A/D	P.SCAN/V-OFF
							0
VOL.	SLEEP	MUTE	VOL.
							CHANNEL/SKIP
	OSD	MENU			BASS	TREBLE	TUNE/SEARCH

1. Switch on the appliance which should be controlled.

2. Press and hold down the Function Selector button for appliance which should be controlled and press SETUP button until the indicator blinking twice.

3. Press the code 9 - 9 - 1.

The indicator will blink twice.

4. Aim the remote control at the appliance and slowly alternate between pressing POWER button and the Function Selector button for the appliance.

5. Stop when the appliance turns off.

6. Press SETUP button once to lock in the code.

CHECKING THE CODE

RESETTING THE ALL CODE
						OSD		MENU
	POWER
							ENTER
	TV	VCR1	DSS/VCR2	DVD	1.	SET UP/		MENU OFF
						T.TONE
1.						PURE DIRECT	AUTO	5	DTS
	TUNER	CD	TAPE	CDR/MD			4		6
							1	2	3
						NIGHT	CSII	EX/ES	VIRTUAL
		AUX1	AMP			DISPLAY	MCH-ST	STEREO	7.1CH IN

TV			MAIN	2.		7	8	9
					CLEAR	MEMO	A/D	P.SCAN/V-OFF
VOL.	SLEEP	MUTE	VOL.
							0
							CHANNEL/SKIP
	OSD	MENU			BASS	TREBLE	TUNE/SEARCH

1. Press and hold down the any Function Selector button and press SETUP button until the indicator blinking twice.

2. Press the code 9 - 8 - 1. The indicator will blink twice.

Then, RC5500SR will return to the factory preset code.

Note:

After this procedure, the selected function button is set initial code and other function buttons are set initial code too.

Once you have found and the codes for your vari- ous appliances, you may want to write them down here.

INPUT/DISC+ AUDIO SUB-T/ATT PTY

1. Press and hold down the Function Selector button for the appliance which should be controlled and press SETUP button until the indicator blinks twice.

2. Press the 4-digit code for appliance (code table at the end of this book)

3. When the procedure is successful, the indicator will blink twice.

1.

POWER

TV	VCR1	DSS/VCR2	DVD
TUNER	CD	TAPE	CDR/MD
	AUX1	AMP

TV			MAIN
VOL.	SLEEP	MUTE	VOL.
	OSD	MENU

1.		ENTER
	SET UP/		MENU OFF
3.	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL
4.		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	8	9
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
2.			0
			CHANNEL/SKIP
	BASS	TREBLE	TUNE/SEARCH

T-MODE RDS F.DIRECT

TV

VCR

DSS

DVD

CD

TAPE

Note:

If the indicator did not blink twice, then repeat steps 1 through 2 and try entering the same code again.

1. Press and hold down the Function Selector button for appliance which should be controlled and press SETUP button until the indicator blinking twice.

2. Press the code 9 - 9 - 0. The indicator will blink twice.

3. To view the code for first digit, press 1 once.

Wait 3 seconds, count the indicator blinks (e.g. 3 blinks = 3) and write down the number.

Note:

If a code digit is “0”, the indicator will not blink.

4. Repeat step 3 three more times for remaining digits. Use 2 for the second digit, 3 for the third digit, and 4 for the fourth digit.

CDR

MD

8