Recording AN Analog Source, Ht-Eq, CH Input | Marantz R3001 specification

ENGLISH

RECORDING AN ANALOG SOURCE

In normal operation, the audio or video source selected for listening through the SR3001 is sent to the record outputs.

This means that any program you are watching or listening to may be recorded simply by placing machines connected to the outputs for TAPE OUT, CD-R/MD OUT, VCR1 OUT, and DSS/VCR2 OUT in the record mode.

To record the input source signal you are currently watching or listening to

POWER

AV SURROUND RECEIVER SR3001

VCR1

DSS/VCR2

DVD

1. TUNER CD TAPE CDR/MD

	AUX1	AMP
TV			MAIIN
VOL.	SLEEP	MUTE	VOL.
	OSD	MENU

1. Select the input source to record by turning the

INPUT FUNCTION SELECTOR knob on the

front panel or simply press the input selector buttons on the remote.

The input source is now selected and you may

Recording the video from one source and the audio from another

You can add the sound from one source to the video of another source to make your own video recordings.

Below is an example of recording the sound from a compact disc player connected to CD IN and the video from a video camera connected to VCR1 to video cassette recorder connected to the DSS/VCR2 OUT jack.

1.	TV	VCR1	DSS/VCR2	DVD
2.	TUNER	CD	TAPE	CDR/MD
2.		AUX1	AMP
	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
	OSD		MENU

1. Switch the video output source to VCR1 by simply pressing the input selector buttons on the remote.

2. Switch the audio input source to CD by simply pressing the input selector buttons on the remote.

3. Now “CD” has been selected as the audio input source and “VCR1” as the video input source.

Notes:

HT-EQ

AV SURROUND RECEIVER SR3001

	SURROUND
	DIGITAL
AAC	PCM

Press the HT-EQbutton on the front panel to turn on the HT-EQ mode.

The tonal balance of a film soundtrack will be excessively bright and harsh when played back over audio equipment in the home. This is because ﬁ lm soundtracks were designed to be played back in large movie theater environments.

Activating the HT-EQ feature when watching a ﬁlm made for movie theaters corrects this and restores the correct tonal balance.

The HT-EQ feature can be activated only while in Dolby Pro Logic Mode, or while decoding Dolby Digital or DTS encoded material.

7.1 CH INPUT

The SR3001 is equipped for future expansion through the use of Multi channel SACD multichannel player or DVD-Audio player.

When this is selected, the input signals connected to the L(front left), R (front right), CENTER, SL (surround left), SR (surround right) and SBL (surround back left) and SBR (surround back right) channels of the 7.1 CH. In jacks are output directly to the front (left and right), center, surround (left and right) and surround back speaker systems as well as the pre-out jacks without passing through the surround circuitry.

In addition, the signal input to the SW (subwoofer) jack is output to the PRE OUT SW (subwoofer) jack. When 7.1 CH. INPUT is selected, the last video input used remains routed to the Monitor Outputs.

This permits simultaneous viewing with video sources

2. 1.

AV SURROUND RECEIVER SR3001	POWER
1.	TV	VCR1	DSS/VCR2	DVD
1.	TUNER	CD	TAPE	CDR/MD
4.		AUX1	AMP
4.	TV			MAIN
	VOL.	SLEEP	MUTE	VOL.
	OSD		MENU

watch or listen to it as desired.

2. The currently selected input source signal is output to the TAPE OUT, CD-R/MD OUT,

VCR1 OUT, and DSS/VCR2 OUT outputs for

recording.

3. Start recording to the recording component as desired.

•If you change the input source during recording, you will record the signals from the newly selected input source.

•You cannot record the surround effects.

•There is no conversion from digital to analog .

When connecting CD players and other digital components, do not connect only the digital terminals, but the analog ones as well.

SURROUND

DIGITAL

		ENTER
	SET UP/		MENU OFF
	T.TONE
	PURE DIRECT	AUTO		DTS
		1	2	3
	NIGHT	CSII	EX/ES	VIRTUAL
2.		4	5	6
	DISPLAY	MCH-ST	STEREO	7.1CH IN
		7	8	9
	CLEAR	MEMO	A/D	P.SCAN/V-OFF
			0

CHANNEL/SKIP

1. Select a desired Video source to decide the routed video signal to the Monitor Outputs .

2. Press the 7.1 CH INPUT button on the front panel or press 7.1 CH IN on the remote to switch the 7.1 channel input.