Great Dane GDRZ26KHE, GDRZ25KHE, GDRZ25KAE manual Storing Safety, Preparing Machine for Storage

Page 34

STORAGE

Storing Safety

cCAUTION: Avoid injury! Fuel vapors are explosive and flammable. Engine exhaust fumes contain carbon monoxide and can cause serious illness or death:

Run the engine only long enough to move the machine to or from storage.

Do not store vehicle with fuel in the tank inside a building where fumes may reach an open flame or spark.

Allow the engine to cool before storing the machine in any enclosure.

Preparing Machine for Storage

1.Repair any worn or damaged parts. Replace parts if necessary. Tighten loose hardware.

2.Repair scratched or chipped metal surfaces to prevent rust.

3.Clean under the deck and remove grass and debris from inside chute and bagger.

4.Wash the machine and apply wax to metal and plastic surfaces.

5.Run machine for five minutes to dry belts and pulleys.

6.Apply light coat of engine oil to pivot and wear points to prevent rust.

Preparing Fuel and Engine for Storage

Fuel:

If you have been using “Stabilized Fuel”, add stabilized fuel to tank until the tank is full.

NOTE: Filling the fuel tank reduces the amount of air in the fuel tank and helps reduce deterioration of fuel.

If you are not using “Stabilized Fuel”:

1. Park machine safely in a well-ventilated area.

NOTE: Try to anticipate the last time the machine will be used for the season so very little fuel is left in the fuel tank.

2.Turn on engine and allow to run until it runs out of fuel.

3.Turn key to off position.

4.Mix fresh fuel and fuel stabilizer in separate container. Follow stabilizer instructions for mixing.

5.Fill fuel tank with stabilized fuel.

6.Run engine for a few minutes to allow fuel mixture to

circulate through carburetor.

Engine:

Engine storage procedure should be used when vehicle is not to be used for longer than 60 days.

1.Change engine oil and filter while engine is warm.

2.Service air filter if necessary.

3.Clean debris from engine air intake screen.

4.Remove spark plugs. Put 30 mL (1 oz.) of clean engine oil in cylinders.

5.Crank the engine five or six times to allow oil to be distributed.

6.Install spark plugs.

7.Clean the engine and engine compartment.

8.Remove battery.

9.Clean the battery and battery posts. Check the electrolyte level.

10.Move fuel shut-off valve to off position.

11.Store the battery in a cool, dry place where it will not freeze.

NOTE: The stored battery should be recharged every 90 days.

12.Charge the battery.

13.Store the vehicle in a dry, protected place. If vehicle is stored outside, put a waterproof cover over it.

Removing Machine From Storage

1.Check tire pressure.

2.Check engine oil level.

3.Check battery electrolyte level. Charge battery if necessary.

4.Install battery.

5.Check spark plug gap. Install and tighten plugs to specified torque.

6.Lubricate all grease points.

7.Turn fuel shut-off valve to on position.

8.Run the engine 5 minutes without the mower or any attachments running to allow oil to be distributed throughout engine.

9.Be sure all shields and guards or deflectors are in place.

Storage - 31

Image 34
Contents OPERATOR’S Manual Special Messages Using Your Operator’s ManualIntroduction Record Identification NumbersTable of Contents Safety Understanding The Machine Safety LabelsOperating Safely Emission Compliance Period Small Off-Road Gas EnginesAgency Category Hours Rotating Blades are Dangerous Checking Mowing AreaParking Safely Avoid TippingChecking Wheel Bolts Practice Safe MaintenanceKeep Riders Off Driving Safely on Public RoadsHandling Fuel Safely Tire SafetyPrevent Fires Fuel and fuel vapors are highly flammable and explosiveOperating Daily Operating ChecklistTesting Safety Systems Console Controls Operating ControlsTesting Neutral Start Safety Switch Testing Park Brake Safety SwitchTesting Park Brake Testing Seat Safety SwitchStopping the Machine Adjusting Cutting HeightOperating the Machine To drive the machine forward Push both control leversMoving the Machine Manually Using the Fuel Shutoff ValvePicture Note Left pump shown Parts Replacement PartsPart Numbers Service Intervals Spray Lubricant Service LubricationGrease Lubrication PointsService Engine Checking Spark Plug Adjusting CarburetorReplacing Fuel Filter Transmission Oil Service TransmissionAdjusting Transmission Neutral Position Checking Transmission Oil LevelRemoving and Installing Traction Drive Belt Bleeding Hydraulic SystemRaise drive wheels off the ground and block caster wheels Adjusting Mower Level Service MowerAdjust Cutting Height Checking and Adjusting Mower Deck Drive Belt Tension Removing and Installing Mower Deck Drive BeltsServicing Mower Blades Checking for Bent Mower BladesBalancing Mower Blades Replacing Mower Spindle Bearings Replacing Mower Deck Idler Pulleys Removing and Installing the Battery Service ElectricalChecking Battery Electrolyte Level Check and Adjust PTO Clutch Air Gap Cleaning Battery and TerminalsReplacing Fuses Kohler Wiring Schematic Checking Wheel Nuts Service MiscellaneousFilling Fuel Tank Servicing Caster Wheel Roller BearingsG, unless the bearings need to be replaced Engine TroubleshootingUsing Troubleshooting Chart CheckMachine Operation ElectricalMower Troubleshooting Preparing Machine for Storage Storing SafetyStorage Preparing Fuel and Engine for StorageAssembly Check Tire Pressure Initial AdjustmentsPTO Clutch Run-in Procedure Level Mower DeckSpecifications Index Belt, Replacing Mower Drive PrimaryPage Service Record GD Record Service Dates