Marantz SR6004, SR5004 Lip.Sync, Using the Sleep Timer, Dual Backup Memory, Recovery of Memory

LIP.SYNC

Depending on the image device (TV, monitor, projector, etc.) connected to the unit a time lag can occur between image signal processing and audio signal processing. Though minor, this time lag can interfere with movie and music enjoyment. The LIP.SYNC feature delays the audio signal with respect to the image signal output from the unit to correct the time lag between the sound and image. It can be operated with the “LIP SYNC” and 1 and 2 cursor buttons of the remote controller. Set the remote controller to the AMP mode before operating the LIP.SYNC feature. The initial setting is OFF (0 ms).The time lag can be adjusted in 10 ms steps up to 200 ms.

Watch the picture on the image device (i.e., TV, monitor, projector, etc.) as you adjust the time lag.

USING THE SLEEP TIMER

To program this unit for automatic standby, press the SLEEP button on the remote controller.

Each press of the button will increase the time before shut down in the following sequence.

OFF 10 20 30 40 50

120 110 100 90 80 70 60

The sleep time will be shown for a few seconds in the display on the front panel, and it will count down until the time has elapsed.

When the programmed sleep time has elapsed, the unit will automatically turn off.

Note that the SLEEP indicator on the display will illuminate when the Sleep function is programmed. To cancel the Sleep function, press the SLEEP button until the display shows “SLEEP OFF” and the SLEEP indicator will disappear.

DUAL BACKUP MEMORY

The unit stores settings information in nonvolatile memory even when the main power supply is turned off. Using the Dual Backup Memory function, you can write settings information to another memory area to back up saved settings for recovery anytime as needed.

BACKUP

Set up the unit in the state for which you want to store the settings. Hold the MEMORY and ENTER buttons on the front panel simultaneously for at least 3 seconds.

“MEMORY SAVING” is displayed and the unit’s settings are saved. The stored settings information is retained until Dual Backup Memory is used again and the information is overwritten.

M E M O R Y S A V I N G

ENGLISH

ADVANCED OPERATION

RECOVERY OF MEMORY

Recover backed up settings as follows.

Hold the MEMORY and MENU buttons on the front panel simultaneously for at least 3 seconds.

“MEMORY LOAD” is displayed and the unit’s stored settings are reapplied.

The unit temporarily enters standby mode. If there is no backup data, “NO BACKUP” is displayed and no data is recovered.

M E M O R Y L O A D

N O B A C K U P

NAMES AND	FUNCTIONS
BASIC	CONNECTIONS
BASIC	OPERATION
ADVANCED	CONNECTIONS
SETUP

Notes

•The LIP.SYNC feature turns OFF (0 ms) in the SOURCE/PURE DIRECT mode. When the SOURCE/PURE DIRECTmode is deactivated, the set value of the LIP.SYNC feature is automatically restored.

•Even if you do not correct the time lag manually this way, audio and video are automatically synchronized when the unit is connected to TV or Projector supporting Auto Lipsync Correction in HDMI 1.3a. For instructions on Auto Lipsync Correction, see page 36.

FRONT KEY (BUTTON) LOCK OF THE UNIT

To lock all front panel buttons (except the POWER ON/ OFF button) and the INPUT SELECTER and VOLUME knobs, hold the PURE DIRECT and EXIT buttons on the front panel simultaneously for at least 3 seconds. At this time, “F-KEY LOCK!” is displayed.

To unlock the controls, press the same buttons again simultaneously for at least 3 seconds. At this time, “F-KEY UNLOCK” is displayed, and the buttons are released.

SURR.	PURE EXIT	CLEAR
MODE	DIRECT

Note

The following settings values cannot be backed up, each Volume value is set to Minimum.

•Main ZONE Volume

•ZONE A Volume

•ZONE Speaker A Volume

ADVANCED OPERATION

TROUBLESHOOTING

OTHERS

43