Dixon ZTR 5017, ZTR 5022 manual 5020, Specifications, Model ZTR

Page 13

SPECIFICATIONS

		Model ZTR	5020
CHASSIS:	11 GA - rectangular tube
BODY:	Two piece - made of rotational molded polyethylene. Front body contains
	access panels for battery service and engine to mower deck belt removal. Rear
	body tilts up to allow service on the entire drive system.
SEAT:	Designed for operator comfort by use of high density closed cell foam padded
	back rest and arm rests, upholstered with CorduraTM water-repellent fabric.
	Seat is adjustable fore and aft.
MOWER DECK:	3 Decks are available. 42" &		60" are made of stamped steel. 50" is made of
	11 GA fabricated welded construction with external reinforcement ribs
	3 blades combine for either a 42", 50", or 60" cut width
	Cut height	approximately 1.5" to 4.5" via 8 position lift handle
BLADE DRIVE:	Electric clutch
DRIVE SYSTEM:	Each rear wheel is independently driven by a HydroGear BDU-10L Series 70
	hydrostatic transmission. The hydrostatic transmissions, in turn, power a fully
	enclosed HydroGear gearbox.
ENGINE:	20HP Briggs & Stratton Intek, overhead valves, replaceable oil filter, full
	pressure lube system, dual element air cleaner, integral fuel pump.
STARTING SYSTEM:	Electric by key switch operation with safety interlocks on parking brake and
	blade drive clutch.
TIRES:	Front	11 X 4 X 5 smooth profile
	Rear	20 X 10.5 X 8 Multi Trac
RECOMMENDED	Front	16 - 21 lbs.
TIRE PRESSURE:	Rear	8 - 14 lbs.
CAPACITIES:	Fuel - 4.8 gallons total (dual tanks)
	Hydrostat oil tank - 3 quart with in-line 10 micron filter
	Hydrostat oil recommendation, refer to page 37
	Engine - 2 qts. SAE 30 (with filter)
DIMENSIONS:	Width	54"(42" Deck), 60"(50" Deck), 73"(60"Deck)
	Height	45"
	Length	72"
	Weight	630 lbs.(42" Deck), 668 lbs. (50" Deck), 685 lbs. (60" Deck)
NOTE:	Additional information provided in service instructions under the individual
	component.

SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Page 13

Image 13

Contents 1999 Operators Manual 5000 SERIESIMPORTANT - READ CAREFULLY 5000 Series INDEXThe most common causes of injury to the operator or bystander SAFETYread and understand this manual to prevent injuries RIDING LAWNMOWERS, IF IMPROPERLY OPERATEDDanger SAFETY SYMBOLSFollow recommended safety precautions and safe operating practices Safety Alert SymbolFailure to observe the following safety instructions could result in SAFETYThis cutting mower is capable of amputating hands & feet and throwing objectsSLOPE OPERATION CHILDREN SERVICE DIXON LIMITED WARRANTY POLICY -- HYDRO-GEAR MODELS SEE DEALER FOR DETAILSWARRANTY DIXON LIMITED WARRANTY POLICY -- ESTATE MODELSModel ZTR SPECIFICATIONS5020 11 GA - rectangular tube CHASSIS1. Grasp seat slide adjuster and move it into adjustment position SEAT ADJUSTMENT INSTRUCTIONS 5000 Series Models2. Slide seat forward or backward 3. Release seat slide adjuster CONTROLS CAUTION Engage parking brake before starting engine PARKING BRAKETO SET PARKING BRAKE HYDRO-GEAR DRIVE SYSTEMTURNING BRAKING TO GO BACKWARDCHOKE CONTROL LEVER THROTTLE CONTROL LEVERCIRCUIT BREAKER BLADE DRIVEMOWER DECK CUT HEIGHT LIFT LEVER BEFORE OPERATING MOWER OPERATION INSTRUCTIONSTOWING If Any Safety Check FAILS Do Not Operate The Mower until TESTING OF SAFETY INTERLOCK SYSTEMSthe system has been checked and repaired by an Authorized Dixon ZTR DealerSTARTING INSTRUCTIONS Engine has been operated STARTING INSTRUCTIONS Cold EngineMOWING WITH A MULCHING ATTACHMENT 6. Maintain Sharp Blades Throughout The Cutting Season MOWING WITH A GRASS CATCHER ATTACHMENTSIDE DISCHARGE OF THE CLIPPINGS Besurethatdeflectorisproperlyinstalledonthe dischargechuteGRASS HEIGHT SUGGESTIONS 5. Maintain Sharp Blades Throughout The Cutting Season60 Deck DECK ROLLERSMAINTENANCE SCHEDULE CARE AND MAINTENANCEBefore performing any maintenance, shut off engine OFF-SEASON BATTERY STORAGEMOWER BLADE MAINTENANCE ENGINE TO MOWER DECK BELT BELT TENSIONBELT FUEL SHUT OFF VALVE SERVICE INTERVALSLUBRICATION LOCATIONSWHEEL REVERSAL REAR WHEELSPROTECT YOUR INVESTMENT CHANGING THE ENGINE OILPLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS PROTECT YOUR ENVIRONMENTMOWER DECK REMOVAL MOWER DECK LEVELING PROCEDURE T-BOX TO HYDROSTAT BELT ADJUSTMENT PARKING BRAKE CABLE ADJUSTMENT NEUTRAL ADJUSTMENT FORWARD TRAVEL SPEED ADJUSTMENT A. AIR GAP ADJUSTMENT PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENTB. OHMS TEST OIL REQUIREMENTS HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICEOIL FILTER P/N 7252- IMPORTANT 3. Put fresh oil in reservoir. Fill reservoir to the full mark WARRANTY CLEANING THE MOWERPARTS/SERVICE WHEELS AND TIRES42 DECK STANDARD SERVICE PARTS LIST50 DECK 60 DECKKOHLER AND BRIGGS & STRATTON AIR AND OIL FILTER PART NUMBERS MOWER CUT QUALITY TROUBLESHOOTINGSITUATION CAUSESDRIVE SYSTEM ELECTRICAL SYSTEM Page MOWER MODEL NUMBER OWNER INFORMATIONPURCHASED FROM MOWER SERIAL NUMBERare registered trademarks of Dixon Industries, Inc Dixon and ZTR5000Series