Dixon ZTR 5022, ZTR 5017 manual Specifications, Model ZTR, Chassis, GA - rectangular tube

Page 14

	SPECIFICATIONS
		Model ZTR 5022
CHASSIS:	11 GA - rectangular tube
BODY:	Two piece - made of high-density polyethylene. Front body contains access
	panels for battery service and engine to mower deck belt removal. Rear body
	tilts up to allow service on the entire drive system.
SEAT:	Designed for operator comfort by use of high density closed cell foam padded
	back and arm rests, upholstered with CorduraTM water-repellent fabric. Seat is
	adjustable fore and aft.
MOWER DECK:	42" Deck:	13 GA Stamped Steel Construction - 42" Cut Width
	50" Deck:	11 GA Fabricated Construction/Reinforcement Ribs - 50" Cut Width
	60" Deck:	10 GA Stamped Steel Construction - 60" Cut Width
		Cut height approximately 1" to 4" via 7 position lift handle
BLADE DRIVE:	Electric clutch
DRIVE SYSTEM:	Each rear wheel is independently driven by a HydroGear BDU-10L Series 70
	hydrostatic transmission. The hydrostatic transmissions, in turn, power a fully
	enclosed HydroGear gearbox.
ENGINE:	22HP Kohler Command, 4-Cycle, V-Configuration, Overhead Valve, Air-Cooled,
	Gasoline, Vertical Shaft, Aluminum Head, and Crankcase with Cast Iron Liners,
	Full Pressure Lubrication/Full Flow Filter, Pulse-type Fuel Pump, Fixed Jet
	Carburetor w/Smart-Choke, Electronic Ignition, In-Line Fuel Filter, Dual Element
	Air Cleaner.
STARTING SYSTEM:	Electric by key switch operation with safety interlocks on parking brake and
	blade drive clutch.
TIRES:	Front	11 X 4 X 5 ribbed tread
	Rear	20 X 10 X 8 Multi Trac
RECOMMENDED	Front	16 - 21 lbs.
TIRE PRESSURE:	Rear	8 - 14 lbs.
CAPACITIES:	Fuel - 4.8 gallons total (dual tanks)
	Hydrostat oil tank - 3 quart with in-line filter
	Hydrostat oil recommendation, refer to page 35
	Engine - 2 qts. SAE 10W30 (with filter)
DIMENSIONS:	Width	51"(42" Deck), 60"(50" Deck), 72"(60" Deck)
	Height	45"
	Length	72"
	Weight	615 lbs.(42" Deck), 680 lbs.(50" Deck), 685 lbs.(60" Deck)
NOTE:	Additional information provided in service instructions under the individual component.
	SPECIFICATIONS SUBJECT TO CHANGE WITHOUT NOTICE

Page 14

Image 14

Contents 5000 SERIES 1999 Operators ManualIMPORTANT - READ CAREFULLY INDEX 5000 Seriesread and understand this manual to prevent injuries SAFETYThe most common causes of injury to the operator or bystander RIDING LAWNMOWERS, IF IMPROPERLY OPERATEDFollow recommended safety precautions and safe operating practices SAFETY SYMBOLSDanger Safety Alert SymbolThis cutting mower is capable of amputating hands & feet SAFETYFailure to observe the following safety instructions could result in and throwing objectsSLOPE OPERATION CHILDREN SERVICE SEE DEALER FOR DETAILS DIXON LIMITED WARRANTY POLICY -- HYDRO-GEAR MODELSDIXON LIMITED WARRANTY POLICY -- ESTATE MODELS WARRANTYSPECIFICATIONS Model ZTR5020 CHASSIS 11 GA - rectangular tube2. Slide seat forward or backward 3. Release seat slide adjuster SEAT ADJUSTMENT INSTRUCTIONS 5000 Series Models1. Grasp seat slide adjuster and move it into adjustment position CONTROLS TO SET PARKING BRAKE PARKING BRAKECAUTION Engage parking brake before starting engine HYDRO-GEAR DRIVE SYSTEMCHOKE CONTROL LEVER TO GO BACKWARDTURNING BRAKING THROTTLE CONTROL LEVERMOWER DECK CUT HEIGHT LIFT LEVER BLADE DRIVECIRCUIT BREAKER TOWING OPERATION INSTRUCTIONSBEFORE OPERATING MOWER the system has been checked and repaired TESTING OF SAFETY INTERLOCK SYSTEMSIf Any Safety Check FAILS Do Not Operate The Mower until by an Authorized Dixon ZTR DealerSTARTING INSTRUCTIONS Cold Engine STARTING INSTRUCTIONS Engine has been operatedMOWING WITH A MULCHING ATTACHMENT MOWING WITH A GRASS CATCHER ATTACHMENT 6. Maintain Sharp Blades Throughout The Cutting SeasonGRASS HEIGHT SUGGESTIONS Besurethatdeflectorisproperlyinstalledonthe dischargechuteSIDE DISCHARGE OF THE CLIPPINGS 5. Maintain Sharp Blades Throughout The Cutting SeasonDECK ROLLERS 60 DeckBefore performing any maintenance, shut off engine CARE AND MAINTENANCEMAINTENANCE SCHEDULE OFF-SEASON BATTERY STORAGEMOWER BLADE MAINTENANCE BELT BELT TENSIONENGINE TO MOWER DECK BELT LUBRICATION SERVICE INTERVALSFUEL SHUT OFF VALVE LOCATIONSREAR WHEELS WHEEL REVERSALPLEASE DISPOSE OF USED OILS AT PROPER COLLECTION CENTERS CHANGING THE ENGINE OILPROTECT YOUR INVESTMENT PROTECT YOUR ENVIRONMENTMOWER DECK REMOVAL MOWER DECK LEVELING PROCEDURE T-BOX TO HYDROSTAT BELT ADJUSTMENT PARKING BRAKE CABLE ADJUSTMENT NEUTRAL ADJUSTMENT FORWARD TRAVEL SPEED ADJUSTMENT B. OHMS TEST PROCEDURE FOR ELECTRIC CLUTCH ADJUSTMENTA. AIR GAP ADJUSTMENT OIL FILTER P/N 7252- IMPORTANT HYDROSTATIC TRANSMISSION OIL AND FILTER SERVICEOIL REQUIREMENTS 3. Put fresh oil in reservoir. Fill reservoir to the full mark PARTS/SERVICE CLEANING THE MOWERWARRANTY WHEELS AND TIRES50 DECK STANDARD SERVICE PARTS LIST42 DECK 60 DECKKOHLER AND BRIGGS & STRATTON AIR AND OIL FILTER PART NUMBERS SITUATION TROUBLESHOOTINGMOWER CUT QUALITY CAUSESDRIVE SYSTEM ELECTRICAL SYSTEM Page PURCHASED FROM OWNER INFORMATIONMOWER MODEL NUMBER MOWER SERIAL NUMBER5000Series Dixon and ZTRare registered trademarks of Dixon Industries, Inc