Black & Decker CCS818R Preparing Your Chain Saw for Use Assembly, Storage Recommendation

Page 10

90560838 ccs818 chain saw.qxd: chainsaw booklet new 2/12/10 10:07 AM Page 10

STORAGE RECOMMENDATION

1. Store tool:

a.) with the battery pack removed and on the charger.

b.) in a place that is cool and dry away from direct sunlight and excess heat or cold.

c.) out of the reach of children.

2.For prolonged storage such as over the winter, the battery pack should be fully charged and then removed from the charger. It should be charged again just prior to use.

LEAVING THE BATTERY PACK IN THE CHARGER

It is OK to leave battery packs on charge for long periods of time. The charger has a maintenance mode which gives the battery pack enough charge to stay “topped off”. If however, the tool is not expected to be needed for more than 30 days, unplug the charger and store battery pack in a cool, dry location. NOTE: A battery pack will lose its charge when kept off of the charger. If the battery pack has not been kept on maintenance charge, it may need to be recharged before use. A battery pack may also lose its charge if left in a charger that is not plugged into an appropriate AC source.

IMPORTANT CHARGING NOTES

1.After normal usage, your battery pack should be fully charged in 6 to 9 hours. If the battery pack is run-down completely, it may take up to 9 hours to become fully charged. Your battery pack was sent from the factory in an uncharged condition. Before attempting to use it, it must be charged for at least 9 hours.

2.DO NOT charge the battery pack in an air temperature below +40°F(+4.5°C), or above +105°F (+40.5°C). This is important and will prevent serious damage to the battery pack. Longest life and best performance can be obtained if battery pack is charged when air temperature is about 75°F (24°C).

3.While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem.

4.If the battery pack does not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which

turns power off when you turn out the lights. (3) Move charger and battery pack to a surrounding air temperature of 40°F (+4.5°C) to 105°F (+40.5°C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the battery pack and charger to your local Black & Decker service center. See Tools Electric in yellow pages.

5.The battery pack should be recharged when it fails to produce sufficient power on jobs which were easily done previously. DO NOT CONTINUE using unit with its battery pack in a depleted condition.

6.The battery pack will reach optimum performance after being cycled 5 times during normal usage. There is no need to run the battery pack down completely before recharging. Normal usage is the best method of discharging and recharging the battery pack.

Preparing Your Chain Saw for Use

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

Assembly

Installing the Guide Bar and Saw Chain

CAUTION: Sharp chain. Always wear protective gloves when handling the chain. The chain is sharp and can cut you when it is not running.

WARNING: Sharp moving chain. To prevent accidental operation, insure that battery is disconnected from the tool before performing the following operations. Failure to do this could result in serious personal injury.

The saw chain and guide bar are packed separately in the carton inside the scabbard. The chain has been placed on the guide bar at the factory to insure that the teeth are facing in the proper direction when you first attach it. Should the chain come off of the guide bar, refer to the section “Replacing the Chain” for proper tooth orientation.

Place the saw on a firm surface. Rotate the two allen head screws (11) counterclockwise with the wrench (13) provided as shown in figure D.

10

Image 10
Contents Volt Cordless Chain Saw Intended use Important Safety InstructionsChain saw names and terms Safety Instructions and Warnings for Chain Saws Power Supply Kickback Safety FeaturesFeatures 17 a Oretreat Direction Fall 45TREE Battery Cap Information ChargingChart for Minimum Wire Size AWG of Extension Cords Charging the Battery PackNameplate Rating Amps 0 10.0 Total Extension Cord Leaving the Battery Pack in the Charger Preparing Your Chain Saw for Use AssemblyInstalling the Guide Bar and Saw Chain Storage RecommendationFollow instructions in Adjusting Chain Tension section Adjusting Chain TensionReplacing the Saw Chain Chain Oiling Connecting the BatteryOperating the Chain Saw Transporting SawCommon Cutting Techniques Oil Level Care and MaintenanceBucking Chain and BarSee ʻTools-Electricʼ Yellow PagesTroubleshooting Section Problem Possible Cause Possible SolutionMode D’EMPLOI Utilisation prévue Terminologie et nomenclature relatives à la scie à chaîneConsignes de sécurité importantes Scies à chaîneVérifier les pièces endommagées Protection contre lʼeffet de rebondBloc dʼalimentation Directives de sécurité concernant lʼeffet de rebondDescription fonctionnelle Conserver CES DirectivesPo 3mm Voie DE Retrait Information concernant le capuchon du bloc-pile Chargement DE LA PileChargement du bloc-piles Recommandations DʼENTREPOSAGE Ensemble DE Piles Dans LE ChargeurPréparation pour lʼutilisation de la scie à chaîne Installation du guide-chaîne et de la chaîneRemplacement de la chaîne AssemblageLubrification de la chaîne Réglage de la tension de la chaîneRemarques Branchement du bloc-piles Fonctionnement de la scie à chaîneTransport de la scie à chaîne DétenteTechniques de coupe les plus communes Niveau dʼhuile Soins et entretienTronçonnage Chaîne et guide-chaîneAccessoires Information SUR LES ReparationsSection de dépannage Problème Cause possible Solution possibleCentral Ave Manual DE Instrucciones Uso previsto Nombres y términos de las sierras de cadenaInstrucciones de seguridad importantes Las sierras de cadenaVerifique que no haya piezas dañadas Manténgase alertaGuarda contra retrocesos Fuente de energía Características de seguridad durante el retrocesoConserve Estas Instrucciones Descripción de las funcionesSímbolos Pulg 3mm Retirada 025 Carga DE LA BateríaEl calibre mínimo requerido Dejando LA Batería EN EL Cargador Carga del paquete de bateríasRecomendacion Para EL Almacenamiento Notas Importantes Sobre LA CargaEnsamblaje Preparación de la sierra de cadena para su usoInstalación de la barra de guía y la cadena de la sierra Reemplazo de la cadena de sierra Ajuste de tensión de la cadenaTransporte de la sierra Operación de la sierra de cadenaLubricación de la cadena NotasSistema de frenos de la cadena Conexión de la bateríaInterruptor Filo de la cadena de la sierraCuidado y mantenimiento Accesorios Informacion DE MantenimientoSección de detección de problemas Problema Causa posible Solución posibleAños DE Garantia Esta Garantia no Aplica CuandoProduct Infomation · Identificacion DEL Producto Solamente Para Propositos DE Mexico Epecificaciones Cargador 120 V, 60HZ Salida 21,75 V DC 210MA
Related manuals
Manual 20 pages 24.2 Kb

CCS818, CCS818R specifications

The Black & Decker CCS818 and CCS818R are innovative cordless electric saws designed for both professional and home use. These lightweight chainsaws are powered by an 18-volt lithium-ion battery, providing the freedom of movement without the constraints of a cord, making them perfect for a variety of cutting tasks in the garden or around the property.

One of the key features of the CCS818 and CCS818R is their 8-inch cutting bar, which allows for efficient cutting of limbs and small trees while ensuring portability and ease of use. Despite their compact size, these saws are capable of cutting through material with confidence, thanks to their robust chain system that grips and cuts smoothly through wood.

In terms of technology, the CCS818 models integrate an automatic oiling system to ensure the chain operates smoothly while reducing wear and tear. This feature simplifies maintenance, allowing users to focus on the task at hand rather than worrying about manual lubrication. Additionally, a transparent oil tank provides a quick view of oil levels, helping users monitor and maintain optimal performance.

The ergonomic design of the CCS818 and CCS818R further enhances their usability. The saws are equipped with a wraparound handle, providing a secure and comfortable grip, which reduces hand fatigue during extended use. The lightweight design also makes these saws user-friendly, especially for those who may not have prior experience handling a chainsaw.

Another characteristic worth mentioning is the tool-free chain tensioning system. This feature allows users to make chain adjustments quickly and easily without the need for additional tools, thus improving workflow efficiency. The CCS818 and CCS818R are also designed with safety in mind, equipped with a chain brake that helps prevent accidents and ensures safe operation.

In summary, the Black & Decker CCS818 and CCS818R chainsaws provide a perfect blend of power and convenience for anyone in need of a reliable cutting tool. Their lightweight design, lithium-ion battery power, automatic oiling, and ease of use make them standout choices for gardening enthusiasts and professionals alike. Whether trimming branches or tackling small tree removals, these chainsaws offer the performance and versatility needed to get the job done efficiently and safely.