Black & Decker CCS818R instruction manual Operating the Chain Saw, Chain Oiling, Transporting Saw

Page 12

90560838 ccs818 chain saw.qxd: chainsaw booklet new 2/12/10 10:07 AM Page 12

1/8 inch (3mm) away from the guide bar (8) with light force from the middle finger and thumb as shown in figure H. There should be no “sag” between the guide bar and the chain on the underside as shown in figure I.

To adjust saw chain tension, loosen the allen head screws (11).

Rotate the tension adjustment screw (23) in the front of the housing using the flat screwdriver end of the wrench (13) as shown in figure F.

Do not over-tension the chain as this will lead to excessive wear and will reduce the life of the bar and chain. Overtensioning also reduces the amount of cuts you will get per battery charge.

Once chain tension is correct, tighten allen head screws (11).

When the chain is new check the tension frequently (after disconnecting battery) during the first 2 hours of use as a new chain stretches slightly.

Chain Oiling

NOTES:

-A high quality bar and chain oil or SAE30 weight motor oil should be used for chain and bar lubrication. Never use waste oil or very thick oil. These may damage your chain saw.

-Replace oil reservoir cap immediately after filling oil reservoir. Failure to do so will allow excessive oil to drip out of oiling outlet.

-It is normal for a small amount of excess oil to drip from the chain saw bar and chain during storage. Do not store chain saw on top of any thing that may be damaged by the dripping oil.

Remove the oil reservoir cap (4) and fill the oil reservoir (3) with the above recommended oil. For best results, keep reservoir over half full.

Lubricate the saw chain as shown in figure J by pressing the bulb on the oil reservoir cap (4) twice before making each cut. Hold bulb down for 3-4 seconds.

Because the saw uses a gravity fed oiling system, the saw should be pointed downward and slightly to the right when applying oil to the chain.

Transporting Saw

Always remove the battery (6) from the tool (figure K) and cover the guide bar (8) with the scabbard (12) (figure L) when

transporting the saw. See the warning under “Battery Cap Information” for additional information on transporting the battery.

Operating the Chain Saw

WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or serious personal injury.

Guard Against Kickback which can result in severe injury or death. See Important Safety Instructions “Guard Against Kickback”, to avoid the risk of kickback.

Do not overreach. Do not cut above chest height. Make sure your footing is firm. Keep feet apart. Divide your weight evenly on both feet.

Use a firm grip with your left hand on the front handle (16) and your right hand on the rear handle (15) so that your body is to the left of the guide bar.

Do not hold chain saw by front hand guard (5). Keep elbow of left arm locked so that left arm is straight to withstand a kickback.

WARNING: Never use a cross-handed grip (left hand on the rear handle and right hand on the front handle).

WARNING: Never allow any part of your body to be in line with the guide bar (8) when operating the chain saw.

Never operate while in a tree, in any awkward position or on a ladder or other unstable surface. You may lose control of saw causing severe injury.

Keep the chain saw running at full speed the entire time you are cutting.

Allow the chain to cut for you. Exert only light pressure. Do not put pressure on chain saw at end of cut.

Connecting the Battery

Place the battery (6) into the tool as shown in figure N and be certain that it is inserted fully into the tool cavity until it “clicks” into place. To remove the battery from the tool, press down on the release button (18) on the back of the battery (figure C) and slide out.

12

Image 12
Contents Volt Cordless Chain Saw Important Safety Instructions Intended useChain saw names and terms Safety Instructions and Warnings for Chain Saws Power Supply Kickback Safety FeaturesFeatures 17 a Oretreat Direction Fall 45TREE Battery Cap Information ChargingCharging the Battery Pack Chart for Minimum Wire Size AWG of Extension CordsNameplate Rating Amps 0 10.0 Total Extension Cord Preparing Your Chain Saw for Use Assembly Installing the Guide Bar and Saw ChainLeaving the Battery Pack in the Charger Storage RecommendationAdjusting Chain Tension Follow instructions in Adjusting Chain Tension sectionReplacing the Saw Chain Connecting the Battery Operating the Chain SawChain Oiling Transporting SawCommon Cutting Techniques Care and Maintenance BuckingOil Level Chain and BarSee ʻTools-Electricʼ Yellow PagesTroubleshooting Section Problem Possible Cause Possible SolutionMode D’EMPLOI Utilisation prévue Terminologie et nomenclature relatives à la scie à chaîneConsignes de sécurité importantes Scies à chaîneVérifier les pièces endommagées Protection contre lʼeffet de rebondBloc dʼalimentation Directives de sécurité concernant lʼeffet de rebondDescription fonctionnelle Conserver CES DirectivesPo 3mm Voie DE Retrait Information concernant le capuchon du bloc-pile Chargement DE LA PileChargement du bloc-piles Recommandations DʼENTREPOSAGE Ensemble DE Piles Dans LE ChargeurInstallation du guide-chaîne et de la chaîne Remplacement de la chaînePréparation pour lʼutilisation de la scie à chaîne AssemblageRéglage de la tension de la chaîne Lubrification de la chaîneRemarques Fonctionnement de la scie à chaîne Transport de la scie à chaîneBranchement du bloc-piles DétenteTechniques de coupe les plus communes Soins et entretien TronçonnageNiveau dʼhuile Chaîne et guide-chaîneAccessoires Information SUR LES ReparationsProblème Cause possible Solution possible Section de dépannageCentral Ave Manual DE Instrucciones Uso previsto Nombres y términos de las sierras de cadenaInstrucciones de seguridad importantes Las sierras de cadenaManténgase alerta Verifique que no haya piezas dañadasGuarda contra retrocesos Fuente de energía Características de seguridad durante el retrocesoDescripción de las funciones Conserve Estas InstruccionesSímbolos Pulg 3mm Retirada 025 Carga DE LA BateríaEl calibre mínimo requerido Carga del paquete de baterías Recomendacion Para EL AlmacenamientoDejando LA Batería EN EL Cargador Notas Importantes Sobre LA CargaPreparación de la sierra de cadena para su uso EnsamblajeInstalación de la barra de guía y la cadena de la sierra Reemplazo de la cadena de sierra Ajuste de tensión de la cadenaOperación de la sierra de cadena Lubricación de la cadenaTransporte de la sierra NotasConexión de la batería InterruptorSistema de frenos de la cadena Filo de la cadena de la sierraCuidado y mantenimiento Accesorios Informacion DE MantenimientoSección de detección de problemas Problema Causa posible Solución posibleAños DE Garantia Esta Garantia no Aplica CuandoProduct Infomation · Identificacion DEL Producto Solamente Para Propositos DE Mexico Epecificaciones Cargador 120 V, 60HZ Salida 21,75 V DC 210MA
Related manuals
Manual 20 pages 24.2 Kb

CCS818, CCS818R specifications

The Black & Decker CCS818 and CCS818R are innovative cordless electric saws designed for both professional and home use. These lightweight chainsaws are powered by an 18-volt lithium-ion battery, providing the freedom of movement without the constraints of a cord, making them perfect for a variety of cutting tasks in the garden or around the property.

One of the key features of the CCS818 and CCS818R is their 8-inch cutting bar, which allows for efficient cutting of limbs and small trees while ensuring portability and ease of use. Despite their compact size, these saws are capable of cutting through material with confidence, thanks to their robust chain system that grips and cuts smoothly through wood.

In terms of technology, the CCS818 models integrate an automatic oiling system to ensure the chain operates smoothly while reducing wear and tear. This feature simplifies maintenance, allowing users to focus on the task at hand rather than worrying about manual lubrication. Additionally, a transparent oil tank provides a quick view of oil levels, helping users monitor and maintain optimal performance.

The ergonomic design of the CCS818 and CCS818R further enhances their usability. The saws are equipped with a wraparound handle, providing a secure and comfortable grip, which reduces hand fatigue during extended use. The lightweight design also makes these saws user-friendly, especially for those who may not have prior experience handling a chainsaw.

Another characteristic worth mentioning is the tool-free chain tensioning system. This feature allows users to make chain adjustments quickly and easily without the need for additional tools, thus improving workflow efficiency. The CCS818 and CCS818R are also designed with safety in mind, equipped with a chain brake that helps prevent accidents and ensures safe operation.

In summary, the Black & Decker CCS818 and CCS818R chainsaws provide a perfect blend of power and convenience for anyone in need of a reliable cutting tool. Their lightweight design, lithium-ion battery power, automatic oiling, and ease of use make them standout choices for gardening enthusiasts and professionals alike. Whether trimming branches or tackling small tree removals, these chainsaws offer the performance and versatility needed to get the job done efficiently and safely.