Blue Rhino 163010 owner manual Assemble Emitter Top, Attach Engine to Post

Page 9

Contact 1-800-762-1142 for assistance.

Do not return to place of purchase.

Step 5 – Assemble Emitter Top

•Slip (1) Small Bolt through hole in Emitter Top from inside.

•Slip (1) Lockwasher over bolt and thread (1) Large nut all the way down and tighten.

•Repeat for other two holes.

Step 6 – Assemble Emitter

•Curl Emitter Screen into a circle. Overlap ends and line up holes. Secure together using (2) Small screws and (2) small nuts.

• Line up holes in bottom of Emitter Screen with holes in Engine.

• Attach Emitter Screen to Engine with (4) Small Screws.

• Line up holes in top of Emitter Screen with holes in Emitter Top.

• Attach Emitter Screen to Emitter Top with (4) Small Screws.

Step 7 – Attach Engine to Post

• Remove and Save Control Knob.

• Remove and save (3) screws from sides and bottom of Engine Access Panel.

•Open Engine Access Panel.

•Disconnect wire from Igniter by gently pulling wire.

•Remove and save Engine Access Panel.

• Align threaded holes in Post with holes in bottom of Engine.

• Insert (4) Medium Screws loosely. They will be fully tightened at the end of the next step.

Note: Do not replace Engine Access Panel until Step 13.

Owner’s manual and assembly instructions: model 163010 natural gas outdoor patio heater

12/4/02

8

Image 9

Contents Manuel d’Utilisation 12/4/02 12/4/02 For Your Safety Safety FirstFor Your Safety Picture Qty General Components & Features Additional RequirementsAttach Legs to Base Attach Cap Assembly to Legs/Insert Gas Line Attach Cylinder Shroud to LegsAssemble Cup, Plate & Ring to Cap Assemble Emitter Top Assemble EmitterAttach Engine to Post Connect Engine/Post Assembly to Cap Connect Gas Line to EngineAttach Dome to Emitter Secure Gas Line Check for LeaksCheck Gas Line / Cylinder valve for leaks Replace Engine Access Panel Install Cylinder Access PanelBefore Turning Gas Supply on Before LightingLighting When heater is on Re-lightingShut Down After Operation Before OperatingIf the problem is This condition exists Then do this TIP Service During periods of extended inactivity or when transportingBetween uses Warranty Period Certifications Safety FeaturesRating Heat Range12/4/02 Avertissement Table des matières Section La sécurité avant tout La sécurité avant toutBonbonne de gaz de 9 kg Pour Votre SécuritéQuincaillerie PiècesAccessoires Supplémentaires Instructions de montageÉtape 1 Fixer les jambes au socle Conseil Étape 7 Fixer le moteur au pôle Étape 6 Assembler l’émetteurÉtape 10 Fixer le dôme à l’émetteur Étape 9 Raccorder la conduite de gaz au moteurÉtape 11 Fixer la conduite de gaz Étape 15 Rechercher une fuite potentielleVérifier la conduite de gaz et la bonbonne Étape 15 Replacer le panneau d’accès du moteur Étape 14 Installer le panneau d’accès de la bonbonneFonctionnement Avant d’ouvrir la commande de gaz onAvant d’allumer l’appareil Allumer l’appareilLorsque l’appareil est allumé on Rallumer l’appareilÉteindre l’appareil Après toute utilisation Vérifications à effectuer avant toute utilisationDans le cas suivant Problème Pour corriger le problème Guide de dépannageEntretien Service après-vente RangementEntre chaque utilisation Période de garantie GarantieCaractéristiques techniques Page NASDAQ-RINO