Aquatic LuxeAir Series owner manual Plumbing, Rough-In Measurements

Page 10

INSTALLATION INSTRUCTIONS

PLUMBING:

1.After securing tub in place, normal waste and overflow and valves are installed per normal plumbing procedures, in accordance with all state and local standards.

2.Install standard 1-1/2” trap to drain and overflow. Before proceeding, make a final operational check by filling tub with water to overflow and operate pump for 5 minutes. Check for leaks carefully both while pump is running and has been turned off. Allow water to stand in tub for at least 30 minutes before draining. AQUATIC INDUSTRIES, INC. WILL NOT BE RESPONSIBLE FOR WATER DAMAGE OF ANY KIND IN CONNECTION WITH ONE OF OUR WHIRLPOOL BATHS.

Rough-In Measurements:

 

 

MODEL

A

B

 

(From center of overflow pipe

(From center of

 

to outside rim)

drain to tub rim)

B

A

5A

LuxeAir 21

6 1/2”

13 1/4”

LuxeAir 22

2 1/4”

12”

LuxeAir 23

5 3/8”

12”

LuxeAir 24

6 3/4”

14”

LuxeAir 25

5 1/4”

16 1/4”

LuxeAir 26

6 1/2”

13 1/2”

LuxeAir 27

2 1/4”

11 1/4”

LuxeAir 28

2 1/4”

11 1/4”

LuxeAir 29

2 1/2”

9 3/8”

LuxeAir 30

2 1/4”

10 1/2”

LuxeAir 31

1 3/4”

10 3/4”

LuxeAir 32

1 5/8”

9 1/4”

LuxeAir 33

3 1/2”

12 1/4”

LuxeAir 34

5 1/2”

13 1/2”

LuxeAir 35

3 1/2”

12 1/2”

LuxeAir 36

5 1/2”

13 1/2”

LuxeAir 37

6”

14”

PLEASE NOTE: The manufacturer accepts a 1/4” variance. There are variations on each tub and specifications are subject to change as we improve upon our product as required.

The dimensions needed for site preparation and structure building will differ; Aquatic Industries, Inc. assumes no responsibility for preparatory work.

10

Aquatic Industries, Inc.

Image 10
Contents Iesluxeair SER Table of Contents Aquatic Industries, Inc Owner InformationAquatic Industries Customer Service Center CongratulationsRead and Follow ALL Instructions Installation Instruction Guidelines Installation Instructions IMPORTANT! Before installation begins, make sure that Factory installed tile flangeAlcove Framing and pre -Installation Procedures Structural PreparationInstallation Procedures for integrally skirted modelS Removable Skirt Panels for Integrally Skirted ModelSPlumbing Rough-In MeasurementsElectrical installation Heater Main Luxeair Block Diagram With Chromatherapy Option Full Size Pressure-Flo Hydrotherapy Jet Operation of LuxeAir seriesLuxEAIR Series Whirlpool Jets Aquatic Rotary Massage Jet11A 11B Stress-Eaz Neck and Shoulder Jets some models11C Full Size Pressure-Flo Hydrotherapy Jets Inline maintenance heater operating instructions12B 12C Air Bath Purge Cycle LuxeAir series Control PanelBATHside Control Systems Automated dry CycleOperation LuxeAir with Optional Chromatherapy Electronic Control Panel see Diagram 11A11A On/Off Control for Jets Pump Optional Chromatherapy LED lighting To Replace BulbWhirlpool system cleaning Maintenance and careAir bath system cleaning Water quality issues Chemical QualityTreatment Fcc consumer information Electrical Installation Information Listed onWhirlpool user information Serial Number LocationRepair Jet CleaningMicrobiological Quality Troubleshooting guide Symptoms Possible problems Suggested solutionsQuantity Description Replacement parts Order formFor LuxEAir series How To Use PriceLuxeair Series Replacement Parts Order Map 11a Assorted Fittings10 a b 12a13a LuxeAir Bath Parts List 93ORBDWO Aquatic Industries, Inc. Limited Lifetime Warranty Page LAOM6 11/08