Aquatic LuxeAir Series Maintenance and care, Whirlpool system cleaning, Air bath system cleaning

Page 22

MAINTENANCE and care

INITIAL CLEANING:

Before tub is used, the whirlpool system should be cleaned and disinfected. Remove all debris and clean tub before putting whirlpool into service. DO NOT USE ABRASIVE CLEANERS ON THE ACRYLIC FINISH. Use a non-abrasive detergent and rinse well after cleaning.

Fill the tub with HOT water to a level 2” above the highest jet.

Add 2 teaspoons of low-sudsing automatic dishwashing detergent and no more than 4 ounces of household bleach to the water.

Operate whirlpool for 10 minutes. Drain. Note: To effectively clean both the whirlpool and air bath system, you must operate them both.

Refill with cold water and operate whirlpool for 5 minutes. Drain.

Whirlpool system cleaning:

To remove accumulations of bath residue from the whirlpool system, we recommend that you purge it at least twice a month, or more depending on usage. To do this, follow this simple procedure. Fill the bath with hot water (not exceeding 140o F). Add to the hot water, 4 (6) tablespoons of low foaming detergent such as liquid Cascade or Calgonite and 24

(48)oz. of liquid household bleach, such as Clorox [use lesser amounts shown for 5-foot bathtubs, greater amounts in parentheses for larger bathtubs]. Run the bath for 5 to 10 minutes. Drain the bath completely and refill with cold water only. Run the whirlpool for 5 to 10 minutes, then drain the bath completely. Depending on the usage and/or the content of the local water supply, more frequent purging may be necessary.

Air bath system cleaning:

NOTE: Do not turn the pump on during the air bath cleaning.

Before tub is used, your air bath and plumbing system should be flushed. Close the drain. Fill bath with hot water to at least six inches above air injector holes. Add 2 teaspoons of low sudsing automatic dishwashing detergent and no more than 4 ounces of bleach to the water. DO NOT use bleach or other chlorinated cleansers on metal trim surrounding control panels. Turn blower on for approximately two minutes to mix cleaner with water. Shut blower down and allow cleaner to soak in the bath for approximately two hours. Turn ON air bath and run for approximately five minutes. Turn air bath unit OFF and drain tub. Aquatic recommends the above cleaning process on your air bath system once a month.

NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.

If you want to use any kind of bath additive, use only a small amount of low-foaming powder or crystal substance; the whirlpool action intensifies the foaming properties of soaps.

The use of certain bubble baths and bath additives may increase the level of accumulations of bath residue in the whirlpool system. If excess accumulations persist, you should discontinue use of these products.

If you have followed the monthly purging instructions and still have an excess accumulation of bath residue and desire an alternative cleaning mechanism, we recommend SUPER SYSTEMS CLEAN PLUS manufactured by Stearns Packaging Corporation to rectify this condition. This may be obtained by calling Aquatic Industries, Inc., at (800) 555-5324. It is recommended that you follow the instructions provided by the manufacturer with the product. Repeated use may be necessary. SUPER SYSTEMS CLEAN PLUS does not replace the necessity to purge your whirlpool system at least twice a month with a low foaming detergent and bleach.

22

Aquatic Industries, Inc.

Image 22
Contents Iesluxeair SER Table of Contents Aquatic Industries, Inc Owner InformationAquatic Industries Customer Service Center CongratulationsRead and Follow ALL Instructions Installation Instruction Guidelines Installation Instructions IMPORTANT! Before installation begins, make sure that Factory installed tile flangeAlcove Framing and pre -Installation Procedures Structural PreparationInstallation Procedures for integrally skirted modelS Removable Skirt Panels for Integrally Skirted ModelSPlumbing Rough-In MeasurementsElectrical installation Heater Main Luxeair Block Diagram With Chromatherapy Option Full Size Pressure-Flo Hydrotherapy Jet Operation of LuxeAir seriesLuxEAIR Series Whirlpool Jets Aquatic Rotary Massage Jet11A 11B Stress-Eaz Neck and Shoulder Jets some models11C Full Size Pressure-Flo Hydrotherapy Jets Inline maintenance heater operating instructions12B 12C Air Bath Purge Cycle LuxeAir series Control PanelBATHside Control Systems Automated dry CycleOperation LuxeAir with Optional Chromatherapy Electronic Control Panel see Diagram 11A11A On/Off Control for Jets Pump Optional Chromatherapy LED lighting To Replace BulbWhirlpool system cleaning Maintenance and careAir bath system cleaning Water quality issues Chemical QualityTreatment Fcc consumer information Electrical Installation Information Listed onWhirlpool user information Serial Number LocationRepair Jet CleaningMicrobiological Quality Troubleshooting guide Symptoms Possible problems Suggested solutionsQuantity Description Replacement parts Order formFor LuxEAir series How To Use PriceLuxeair Series Replacement Parts Order Map 11a Assorted Fittings10 a b 12a13a LuxeAir Bath Parts List 93ORBDWO Aquatic Industries, Inc. Limited Lifetime Warranty Page LAOM6 11/08