Aquatic LuxeAir Series owner manual Electrical installation

Page 11

INSTALLATION INSTRUCTIONS

electrical installation:

WARNING: ALL ELECTRICAL CONNECTIONS SHOULD BE MADE BY A LICENSED, LOCALLY CERTIFIED ELECTRICIAN, IN ACCORDANCE WITH THE REQUIREMENTS OF THE NATIONAL ELECTRICAL CODES AND PROCEDURES.

WARNING: When using electrical products, precautions should always be followed, including the following:

DANGER: RISK OF ELECTRIC SHOCK!

GFCIs are not supplied, however we do specify their use.

All known code authorities require GFCIs.

LuxeAir baths will need to be hard-wired to the outlets provided. See the following directions and diagram on page 12.

Two junction boxes will be mounted to the frame of the whirlpool. One of the two boxes will have one outlet and will be labeled “Blower”. Remove the cover and connect a 14/2 with ground Romex wire from a 15 amp 1-pole GFCI breaker (not supplied) in the main circuit breaker panel. Connect the black wire to the hot side of the receptacle, the white wire to the neutral side of the receptacle and the green wire to ground. Replace the cover and plug in the blower. (See diagram on page 12).

The second junction box will have two outlets, one labeled “Main” and the other labeled “Heater”. Remove the cover. Run Romex 14/3 with ground from a 15 amp 2-pole GFCI breaker (not supplied) located in the breaker panel. Connect the white wire (neutral) to both neutrals of the two outlets. Connect the red wire (hot) to the hot terminal of the outlet labeled “Main”. Connect the black wire (hot) to the hot terminal of the other outlet labeled “Heater”. Connect the green wire (ground) to the ground terminal of the outlet. Replace the cover of the junction box. Find the pump cord and plug it into the outlet labeled “Heater”. Plug the cord labeled “Main AC Input” into the outlet labeled “Main” (See diagram on page 12).

CAUTION: Before use of the pump and heater, test the GFCI for proper operation. The pump and heater should turn off when the GFCI “Test” button is pushed.

Aquatic Industries, Inc.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Iesluxeair SER Table of Contents Owner Information Aquatic Industries, IncCongratulations Aquatic Industries Customer Service CenterRead and Follow ALL Instructions Installation Instruction Guidelines Installation Instructions Structural Preparation Factory installed tile flangeAlcove Framing and pre -Installation Procedures IMPORTANT! Before installation begins, make sure thatRemovable Skirt Panels for Integrally Skirted ModelS Installation Procedures for integrally skirted modelSRough-In Measurements PlumbingElectrical installation Heater Main Luxeair Block Diagram With Chromatherapy Option Aquatic Rotary Massage Jet Operation of LuxeAir seriesLuxEAIR Series Whirlpool Jets Full Size Pressure-Flo Hydrotherapy Jet11C Stress-Eaz Neck and Shoulder Jets some models11A 11B 12B 12C Inline maintenance heater operating instructionsFull Size Pressure-Flo Hydrotherapy Jets Automated dry Cycle LuxeAir series Control PanelBATHside Control Systems Air Bath Purge Cycle11A Electronic Control Panel see Diagram 11AOperation LuxeAir with Optional Chromatherapy On/Off Control for Jets Pump To Replace Bulb Optional Chromatherapy LED lightingAir bath system cleaning Maintenance and careWhirlpool system cleaning Chemical Quality Water quality issuesTreatment Serial Number Location Electrical Installation Information Listed onWhirlpool user information Fcc consumer informationMicrobiological Quality Jet CleaningRepair Symptoms Possible problems Suggested solutions Troubleshooting guidePrice Replacement parts Order formFor LuxEAir series How To Use Quantity DescriptionLuxeair Series Replacement Parts Order Map 12a Assorted Fittings10 a b 11a13a LuxeAir Bath Parts List 93ORBDWO Aquatic Industries, Inc. Limited Lifetime Warranty Page LAOM6 11/08
Top Page Image Contents