Alamo 6, 5 manual Safety

Page 12
(SG-25)
(SG-24)
(SG-23)
(SG-22)
(SG-19)

SAFETY

SAFETY

Transport only at speeds where you can maintain control of the equipment. Serious accidents and injuries can result from operating this equipment at high speeds. Understand the Tractor and Implement and how it handles

before transporting on streets and highways. Make sure the Tractor steering and brakes are in good condition and operate properly.

Before transporting the Tractor and Implement, determine the proper transport speeds for you and the equipment. Make sure you abide by the following rules:

Test the tractor at a slow speed and increase the speed slowly. Apply the Brakes smoothly to determine the stopping characteristics of the Tractor and Implement. As you increase the speed of the Tractor the stopping distance increases. Determine the maximum transport speed not to exceed 20 mph (30 kph) for transporting this equipment.

Test the equipment at a slow speed in turns. Increase the speed through the turn only after you determine that the equipment can be operated at a higher speed. Use extreme care and reduce your speed when turning sharply to prevent the tractor and implement from turning over. Determine the maximum turning speed for you and this equipment before operating on roads or uneven ground.

Only transport the Tractor and Implement at the speeds which allow you to properly control the equipment.

Be aware of the operating conditions. Do not operate the Tractor with weak or faulty brakes or worn tires. When operating down a hill or on wet or rain slick roads, the braking distance increases: use extreme care and reduce your speed. When operating in traffic always use the Tractor’s flashing warning lights and reduce your speed. Be aware of traffic around you and watch out for the other guy.

Always read carefully and comply fully with the manufacturer’s instructions when handling oil, solvents, cleansers, and any other chemical agent.

Never run the Tractor engine in a closed building or without adequate ventilation. The exhaust fumes can be hazardous to your health.

KEEP AWAY FROM ROTATING ELEMENTS to prevent entanglement and possible serious injury or death.

Never allow children to play on or around Tractor or Implement. Children can slip or fall off the Equipment and be injured or killed. Children can cause the Implement to shift or fall crushing themselves or others.

SB5/6 03/09

Safety Section 1-6

© 2009 Alamo Group Inc.

Image 12
Contents Switchblade 5/6 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Ledger Plates Safety Section Safety SB5/6 03/09 Safety Section Safety Safety Safety Safety S3PT-4 SBM-7 Safety See Your Alamo Dealer Safety QTY Type Description Peligro Decal Description Safety Instructions Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Operation Section Operation Operation Operator RequirementsTractor Safety Devices Tractor HorsepowerTractor Requirements Tractor Requirements and CapabilitiesFront End Weight Power Take Off PTOGetting on and OFF the Tractor Tractor HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/Service Sickle Bar Pre-Operation Inspection/ServiceFrame Assembly OPS-SB Hydraulic PUMP/OIL Reservoir Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Switch Blade Operating the Tractor and Implement Motor Control Cutter BAR BREAK-BACK Operating the Switch Blade Shutting Down the Switch Blade Tractor and Switch Blade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Operation Hauling the Tractor and Implement Page Maintenance Section Maintenance Lubrication InformationInitial Hydraulic System Cleaning Reservoir OIL & Filter MaintenanceCutterbar Adjustments Guard AdjustmentCutterbar Alignment Wear Plate ClipsSB5/6 03/09 Maintenance Section Hydraulic System Pump & MotorCylinder Rod Maintenance Ledger PlatesPage ALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER Switchblade 5/6 SOM 03/09