Alamo 6, 5 Tractor Requirements and Capabilities, Rops and Seat Belt, Tractor Safety Devices

Page 78
(SG-7)

OPERATION

OPERATION

2.TRACTOR REQUIREMENTS

The tractor used to operate the mower must have the power capacity to lift, pull, and operate the Power Take Off (PTO) at the mower’s rated speed while traveling at a ground speed between 2 and 5 MPH. Operating the mower with a tractor that does not meet the following requirements may cause tractor or mower damage and be a potential danger to the operator and passersby.

Tractor Requirements and Capabilities

ASAE approved Roll-Over Protective Structure (ROPS) or ROPS cab and seat belt.

Tractor Safety Devices .................... Slow Moving Vehicle (SMV) emblem, lighting,

Tractor Horsepower:

-Minimum

25 HP

Front End Weights............................ As needed to maintain 20% weight on front axle

Power Take Off................................. 540 RPM 6-spline or 1000 RPM 21-spline shaft

2.1ROPS and Seat Belt

The tractor must be equipped with a Roll-Over-Protective-Structure (ROPS) (tractor cab or roll-bar) and seat belt to protect the operator from falling off the tractor, especially during a roll over where the driver could be crushed and killed. Only operate the tractor with the ROPS in the raised position and seat belt fastened. Tractor model not equipped with a ROPS and seat belt should have these life saving features installed by an authorized dealer. OPS-U- 0003

Operate this Equipment only with a Tractor equipped with an approved roll- over-protective system (ROPS). Always wear seat belts. Serious injury or even death could result from falling off the tractor--particularly during a turnover when the operator could be pinned under the ROPS.

2.2 Tractor Safety Devices

If transporting or operating the tractor and implement near a public roadway, the tractor must be equipped with proper warning lighting and a Slow Moving Vehicle (SMV) emblem which are clearly visible from the rear of the unit. Lights and a SMV emblem must be equipped directly on implements if the visibility of the tractor warning signals are obscured.

Maintain all manufacturer equipped safety shields and guards. Always replace shields and guards that were removed for access to connect, service, or repair the tractor or implement. Never operate the tractor PTO with the PTO master shield missing or in the raised position. OPS-U- 0004

2.3 Tractor Horsepower

The power required to operate a mower is determined by the tractor PTO horsepower. For most mowing conditions, the Switch Blade mower requires a tractor with at least 25 HP for a 5 and 6 unit. Operating the mower with a tractor that does not have adequate power may damage the tractor engine. Exceeding 25 HP may cause mower damage by overpowering the unit in heavy cutting conditions.

SB5/6 03/09

Operation Section 3-4

© 2009 Alamo Group Inc.

Image 78
Contents Switchblade 5/6 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Ledger Plates Safety Section Safety SB5/6 03/09 Safety Section Safety Safety Safety Safety S3PT-4 SBM-7 Safety See Your Alamo Dealer Safety QTY Type Description Peligro Decal Description Safety Instructions Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Operation Section Operation Operation Operator RequirementsTractor Requirements Tractor Safety DevicesTractor Horsepower Tractor Requirements and CapabilitiesGetting on and OFF the Tractor Front End WeightPower Take Off PTO Tractor HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/Service Sickle Bar Pre-Operation Inspection/ServiceFrame Assembly OPS-SB Hydraulic PUMP/OIL Reservoir Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Switch Blade Operating the Tractor and Implement Motor Control Cutter BAR BREAK-BACK Operating the Switch Blade Shutting Down the Switch Blade Tractor and Switch Blade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Operation Hauling the Tractor and Implement Page Maintenance Section Maintenance Lubrication InformationInitial Hydraulic System Cleaning Reservoir OIL & Filter MaintenanceCutterbar Adjustments Guard AdjustmentCutterbar Alignment Wear Plate ClipsSB5/6 03/09 Maintenance Section Hydraulic System Pump & MotorCylinder Rod Maintenance Ledger PlatesPage ALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER Switchblade 5/6 SOM 03/09