Alamo 6, 5 manual Safety

Page 8
(SG-1)

SAFETY

SAFETY

General Safety Instructions and Practices

A careful operator is the best operator. Safety is of primary importance to the manufacturer and should be to the owner/operator. Most accidents can be avoided by being aware of your equipment, your surroundings, and observing certain precautions. The first section of this manual includes a list of Safety Messages that, if followed, will help protect the operator and bystanders from injury or death. Read and understand these Safety Messages before assembling, operating or servicing this Implement. This equipment should only be operated by those persons who have read the manual, who are responsible and trained, and who know how to do so responsibly.

The Safety Alert Symbol combined with a Signal Word, as seen below, is used throughout this manual and on decals which are attached to the equipment. The Safety Alert Symbol means: “ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!” The Symbol and Signal Word are intended to warn the owner/operator of impending hazards and the degree of possible injury faced when operating this equipment.

Practice all usual and customary safe working precautions and above all---remember safety is up to YOU. Only YOU can prevent serious injury or death from unsafe practices.

Indicates an imminently hazardous situation that, if not avoided, WILL result in DEATH OR VERY SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, COULD result in DEATH OR SERIOUS INJURY.

Indicates an imminently hazardous situation that, if not avoided, MAY result in MINOR INJURY.

Identifies special instructions or procedures that, if not strictly observed, could result in damage to, or destruction of the machine, attachments or the environment.

NOTE: Identifies points of particular interest for more efficient and convenient operation or repair.

READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2)

Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3)

SB5/6 03/09

Safety Section 1-2

© 2009 Alamo Group Inc.

Image 8
Contents Switchblade 5/6 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Ledger Plates Safety Section Safety SB5/6 03/09 Safety Section Safety Safety Safety Safety S3PT-4 SBM-7 Safety See Your Alamo Dealer Safety QTY Type Description Peligro Decal Description Safety Instructions Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Operation Section Operation Operation Operator RequirementsTractor Safety Devices Tractor HorsepowerTractor Requirements Tractor Requirements and CapabilitiesFront End Weight Power Take Off PTOGetting on and OFF the Tractor Tractor HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/Service Sickle Bar Pre-Operation Inspection/ServiceFrame Assembly OPS-SB Hydraulic PUMP/OIL Reservoir Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Switch Blade Operating the Tractor and Implement Motor Control Cutter BAR BREAK-BACK Operating the Switch Blade Shutting Down the Switch Blade Tractor and Switch Blade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Operation Hauling the Tractor and Implement Page Maintenance Section Maintenance Lubrication InformationInitial Hydraulic System Cleaning Reservoir OIL & Filter MaintenanceCutterbar Alignment Cutterbar AdjustmentsGuard Adjustment Wear Plate ClipsSB5/6 03/09 Maintenance Section Hydraulic System Pump & MotorCylinder Rod Maintenance Ledger PlatesPage ALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER Switchblade 5/6 SOM 03/09