Alamo 6, 5 manual Operation

Page 76
Si no lee ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3)
Operation Section 3-2
OPERATION
ALAMO INDUSTRIAL SWITCH BLADE SICKLE BAR
OPERATING INSTRUCTIONS
Alamo Industrial Switch Blade are manufactured with quality material by skilled workers. The Switch Blade is designed for cutting grass and weeds up to 1/2” diameter such as in rights-of-way and roadsides. The Switch Blade is equipped with safety warning decals, protective guards, shields, and other safety features to provide operator and passerby protection, however, no shielding is 100% accurate. ALL safety equipment and safety warning decals must be maintained on the unit in good operational condition at all times.
It is the operator’s responsibility to be knowledgeable of all potential operating hazards and to take every reasonable precaution to ensure oneself, others, animals, and property are not injured or damaged by the unit, tractor or a thrown object. Do not operate the unit if bystanders, passersby, pets or livestock are within 300 feet of the unit.
This section of the Operator’s Manual is designed to familiarize, instruct, and educate operators to the safe and proper use of the Switch Blade. Pictures contained in this section are intended to be used as a visual aid to assist in explaining the operation of a Switch Blade and are not specific to a Switch Blade. Some pictures may show shields removed to enhance visual clarity. NEVER operate the unit without all safety equipment in place and in good operational condition. The operator must be familiar with the unit and tractor operation and all safety practices before beginning operation. Proper operation, as detailed in this manual, will help ensure years of safe and satisfactory use of the Switch Blade.
READ AND UNDERSTAND THE ENTIRE OPERATING INSTRUCTIONS AND SAFETY SECTION OF THIS MANUAL AND THE TRACTOR MANUAL BEFORE ATTEMPTING TO USE THE TRACTOR AND IMPLEMENT. If you do not understand any of the instructions, contact your nearest authorized dealer for a full explanation. Pay close attention to all safety signs and safety messages contained in this manual and those affixed to the implement and tractor. OPS-U- 0001
READ, UNDERSTAND, and FOLLOW the following Safety Messages. Serious injury or death may occur unless care is taken to follow the warnings and instructions stated in the Safety Messages. Always use good common sense to avoid hazards. (SG-2)

OPERATION

SB5/6 03/09

© 2009 Alamo Group Inc.

Image 76
Contents Switchblade 5/6 To the Owner/Operator/Dealer Page Alamo Industrial Division is willing to provide Table of Contents Ledger Plates Safety Section Safety SB5/6 03/09 Safety Section Safety Safety Safety Safety S3PT-4 SBM-7 Safety See Your Alamo Dealer Safety QTY Type Description Peligro Decal Description Safety Instructions Safety Federal Laws and Regulations Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Page Introduction Section Introduction Introduction Before Operating this Machine Operation Section Operation Operation Operator RequirementsTractor Safety Devices Tractor HorsepowerTractor Requirements Tractor Requirements and CapabilitiesFront End Weight Power Take Off PTOGetting on and OFF the Tractor Tractor HydraulicsBoarding the Tractor Dismounting the TractorStarting the Tractor PRE-OPERATION Inspection and Service Tractor Pre-Operation Inspection/Service Sickle Bar Pre-Operation Inspection/ServiceFrame Assembly OPS-SB Hydraulic PUMP/OIL Reservoir Driving the Tractor and Implement Brake and Differential Lock Setting Starting the TractorDriving the Tractor and Switch Blade Operating the Tractor and Implement Motor Control Cutter BAR BREAK-BACK Operating the Switch Blade Shutting Down the Switch Blade Tractor and Switch Blade Storage Transporting the Tractor and ImplementTransporting on Public Roadways Operation Operation Hauling the Tractor and Implement Page Maintenance Section Maintenance Lubrication InformationInitial Hydraulic System Cleaning Reservoir OIL & Filter MaintenanceGuard Adjustment Cutterbar AdjustmentsCutterbar Alignment Wear Plate ClipsSB5/6 03/09 Maintenance Section Hydraulic System Pump & MotorCylinder Rod Maintenance Ledger PlatesPage ALAMO-INDUSTRIAL To the OWNER/OPERATOR/DEALER Switchblade 5/6 SOM 03/09