Alamo 95C manual Mounting Backhoe to Tractor

Page 32

ASSEMBLY

ASSEMBLY

MOUNTING BACKHOE TO

TRACTOR

1.Back tractor close enough to backhoe to connect hose kit or pump to tractor.

WARNING: BEFORE leaving the Power Unit Seat, always engage the brake and set the Power Unit transmission in parking gear, disengage the auxiliary hydraulics, stop the engine, remove the key, and wait for all moving parts to stop.

2.Using backhoe hydraulics, lower stabilizers until backhoe can be connected to 3-point hitch. Bottom of backhoe boom pivot should be 8 to 12 inches off ground when attaching to tractor lower 3-point arms.

3.Connect lower 3-point hitch members to backhoe and secure using linch pins from 3-point hitch.

4.Connect link assembly to upper connecting point on 3- point hitch using clevis pin and linch pin from 3-point hitch.

NOTE: Insert adapter tube (5) in end of link assembly if necessary to adapt to smaller 3-point connecting pin.

5.Adjust link assembly length if necessary for backhoe mainframe to rest in vertical position.

NOTE: Adjustment limitations are shown in Figure 3.

6.Check for proper operator head clearance with ROPS and cab (Figure 4).

7.Tighten all hardware in upper link assembly to torque specifications in backhoe manual.

WARNING: Escaping hydraulic fluid under pressure can penetrate skin causing serious injury.

•DO NOT use your hands to check for leaks. Use a piece of cardboard or paper to search for leaks.

Stop engine and relieve pressure before connecting or disconnecting lines.

Tighten all connections before starting engine or pressurizing lines.

If any fluid is injected into skin, obtain medical attention immediately or gangrene may result.

F-4145 01/11

Assembly Section 3-4

© 2011 Alamo Group Inc.

Image 32
Contents 95C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Safety Safety Safety Equipment Operation Safety Instructions and Practices SBH-14 Safety Safety SBH-44 Transporting Safety Instructions and Practices Death. SBH-27 Storage Safety Instructions and Practices Parts Information See Your Rhino DealerDecal Location QTY Level Description Decal Description Safety Federal Laws and Regulations Page Introduction Section Introduction Cylinder Data General DataBucket Data Introduction Assembly Section Assembly Installing Three Point Adapter Option Mounting Backhoe to Tractor Operation Section PRE-OPERATION Checklist Operating DirectionsEngine Speed ControlsOperating Backhoe Left Hand StabilizerRight Hand Stabilizer Trenching Between a Building & Open Excavators Filling BucketDumping Bucket Side Slope Excavating or Trenching Miscellaneous Finishing Straight WallsMounting and Dismounting Buckets Seat AdjustmentBackfilling Placing the Stabilizers Swing LockBoom Lock Stabilizer LockRemoval from Tractor Storage Page Maintenance Section Cylinder Assembly Cylinder ServiceCylinder Disassembly Hydraulic System Reservoir Beginning of SeasonHydraulic Hoses Lubrication Chart Bucket Tooth PointsTightening Nuts and Bolts LubricationHydraulic Troubleshooting Maintenance Valve Service Main Relief ReplacementSpool Seal Installation Torque SettingsMaintenance Parts List Description QTYProper Torque for Fasteners Page Rhino Required of the Owner 95C-SOM-01/11 F-4145C Printed U.S.A

95C specifications

The Alamo 95C is a sophisticated compact tractor that has been designed to meet the demands of both agricultural and light industrial applications. With its robust construction and versatile functionalities, it has become a popular choice among farmers, landscapers, and small property owners.

One of the standout features of the Alamo 95C is its powerful engine. Equipped with a reliable diesel power plant, it delivers impressive performance while maintaining fuel efficiency. The engine is tailored to produce high torque at low RPM, ensuring that the tractor can handle tough tasks with ease, from plowing fields to hauling heavy loads.

The Alamo 95C is designed for ease of operation. It features an ergonomic control layout and a comfortable operator platform, allowing for prolonged use without causing fatigue. The intuitive controls and simplified interface make it accessible even for less experienced operators. Its tight turning radius enhances maneuverability, making it ideal for working in confined spaces.

In terms of technology, the Alamo 95C is outfitted with modern electronic systems that improve overall performance and efficiency. The tractor comes with a digital dashboard that provides real-time data on engine parameters, fuel levels, and other vital statistics. This allows operators to monitor performance closely and make informed decisions while working.

The Alamo 95C is also designed with versatility in mind. It can be outfitted with a range of attachments, including loaders, backhoes, and mowers, enabling it to adapt to various tasks. The three-point hitch system allows for easy attachment of implements, while the Power Take-Off (PTO) system ensures that it can power a variety of tools and equipment.

Durability is another key characteristic of the Alamo 95C. Its frame is constructed from high-quality materials, ensuring it can withstand harsh working conditions. Additionally, it has been engineered for ease of maintenance, with accessible components that simplify routine checks and repairs.

Overall, the Alamo 95C combines power, efficiency, and versatility, making it an excellent investment for anyone looking to maximize productivity on their property. With its advanced features and robust design, it continues to set a standard in the compact tractor market. Whether for agricultural purposes or landscaping tasks, the Alamo 95C proves to be a dependable and efficient workhorse.