Alamo 95C manual Cylinder Service, Cylinder Disassembly, Cylinder Assembly

Page 44

MAINTENANCE

MAINTENANCE

CYLINDER SERVICE

Cylinder are designed to be reliable and easy to service. If a cylinder should malfunction during warranty period, return complete cylinder assembly, without disassembling, to your authorized service department for instructions. Unauthorized disassembly of a cylinder in warranty period will VOID WARRANTY.

Following is an outline procedure for disassembling and reassembling cylinders.

CYLINDER DISASSEMBLY

1.Hold cylinder tube (13) stationary and pull wire ring

(14)out through slot. Rotate head (6) to ease disassembly.

2.Pull shaft (1), with all assembled parts, out of cylinder tube.

NOTE: Resistance will be felt until piston seal (10) slides over wire retaining ring groove. Seal is usually damaged when cylinder is disassembled.

3.Remove lock nut (12) from end of shaft and slide piston (8) and cylinder head (6) off shaft.

4.Remove piston wear ring (11), piston seal (10) and o- ring (9) from outside grooves on piston (Swing cylinders have additional steel ring between piston and nut).

5.Remove wiper seal (2), rod seal (3) and wear ring (7) from inside of cylinder head and o-ring (5) with backup washer (4) from groove on outside of head.

6.Clean all parts including cylinder tube, in a suitable cleaning solvent, then use air pressure to blow any dirt or excess solvent from all parts.

7.Examine all parts for wear or damage and replace, if necessary.

CYLINDER ASSEMBLY

Note: Be careful not to damage seals and o-rings on edges or holes in cylinder tube. Inspect and remove burrs and sharp edges if necessary before reassembly.

1.Place rod seal (3) into groove inside cylinder head.

NOTE: Lips of seal (3) must face inward and seal must be firmly seated in groove. For easier installation, place seal

(3) in 120°F water to warm seal.

2.Install wiper seal (2) with lip of seal facing out and flush with top of cylinder head. Install wear ring (7) inside other end of head.

3.Place o-ring (5) with backup washer (4) in groove on outside of head. Backup washer must be on rod side.

4.Remove sharp edges on outer edge of threaded end of shaft (1). Lubricate wiper seal (2) and rod seal (3) in head and carefully slide head onto shaft.

5.Place o-ring (9), piston seal (10) and piston wear ring (11) in grooves on outside of piston.

NOTE: For easier installation, place piston seal (10) in 120°F water to warm seal.

6.Slide piston onto threaded end of shaft and install lock nut (12). Swing, bucket and stabilizers cylinders; tighten lock nut (12) to 300 ft./lbs. Lift and dipperstick cylinders; tighten lock nut (12) to 375 ft./lbs. on lift cylinders.

7.Lubricate piston wear ring (11) and piston seal (10) on piston, o-ring (5) and backup washer (4) on head and inside of cylinder tube (13), then carefully slide piston and head into cylinder tube.

8.Insert wire retaining ring (14) into slot in cylinder tube (13). Apply pressure to wire ring to thread it into groove while turning cylinder head.

F-4145 01/11

Maintenance Section 5-2

© 2011 Alamo Group Inc.

Page 43 Page 45
Image 44
Page 43 Page 45
Contents 95C To the OWNER/OPERATOR/DEALER Table of Contents Page Safety Section Safety Safety Safety Safety Equipment Operation Safety Instructions and Practices SBH-14 Safety Safety SBH-44 Transporting Safety Instructions and Practices Death. SBH-27 Storage Safety Instructions and Practices Parts Information See Your Rhino DealerDecal Location QTY Level Description Decal Description Safety Federal Laws and Regulations Page Introduction Section Introduction Cylinder Data General DataBucket Data Introduction Assembly Section Assembly Installing Three Point Adapter Option Mounting Backhoe to Tractor Operation Section PRE-OPERATION Checklist Operating DirectionsEngine Speed ControlsOperating Backhoe Left Hand StabilizerRight Hand Stabilizer Trenching Between a Building & Open Excavators Filling BucketDumping Bucket Side Slope Excavating or Trenching Miscellaneous Finishing Straight WallsMounting and Dismounting Buckets Seat AdjustmentBackfilling Placing the Stabilizers Swing LockBoom Lock Stabilizer LockRemoval from Tractor Storage Page Maintenance Section Cylinder Assembly Cylinder ServiceCylinder Disassembly Hydraulic System Reservoir Beginning of SeasonHydraulic Hoses Lubrication Chart Bucket Tooth PointsTightening Nuts and Bolts LubricationHydraulic Troubleshooting Maintenance Valve Service Main Relief ReplacementSpool Seal Installation Torque SettingsMaintenance Parts List Description QTYProper Torque for Fasteners Page Rhino Required of the Owner 95C-SOM-01/11 F-4145C Printed U.S.A

95C specifications

The Alamo 95C is a sophisticated compact tractor that has been designed to meet the demands of both agricultural and light industrial applications. With its robust construction and versatile functionalities, it has become a popular choice among farmers, landscapers, and small property owners.

One of the standout features of the Alamo 95C is its powerful engine. Equipped with a reliable diesel power plant, it delivers impressive performance while maintaining fuel efficiency. The engine is tailored to produce high torque at low RPM, ensuring that the tractor can handle tough tasks with ease, from plowing fields to hauling heavy loads.

The Alamo 95C is designed for ease of operation. It features an ergonomic control layout and a comfortable operator platform, allowing for prolonged use without causing fatigue. The intuitive controls and simplified interface make it accessible even for less experienced operators. Its tight turning radius enhances maneuverability, making it ideal for working in confined spaces.

In terms of technology, the Alamo 95C is outfitted with modern electronic systems that improve overall performance and efficiency. The tractor comes with a digital dashboard that provides real-time data on engine parameters, fuel levels, and other vital statistics. This allows operators to monitor performance closely and make informed decisions while working.

The Alamo 95C is also designed with versatility in mind. It can be outfitted with a range of attachments, including loaders, backhoes, and mowers, enabling it to adapt to various tasks. The three-point hitch system allows for easy attachment of implements, while the Power Take-Off (PTO) system ensures that it can power a variety of tools and equipment.

Durability is another key characteristic of the Alamo 95C. Its frame is constructed from high-quality materials, ensuring it can withstand harsh working conditions. Additionally, it has been engineered for ease of maintenance, with accessible components that simplify routine checks and repairs.

Overall, the Alamo 95C combines power, efficiency, and versatility, making it an excellent investment for anyone looking to maximize productivity on their property. With its advanced features and robust design, it continues to set a standard in the compact tractor market. Whether for agricultural purposes or landscaping tasks, the Alamo 95C proves to be a dependable and efficient workhorse.
Top Page Image Contents