Exmark 920 manual Disengaging the PTO, Stopping the Engine, Driving the Machine

Page 23

Operation

The PTO push-pull switch engages the cutting blades. Be sure that all persons are clear of the mower deck and discharge area before engaging PTO.

Important: Operator must be in seat before the PTO can be engaged.

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Pull the PTO switch outward to engage the blades.

3.Place the throttle in the “FAST” position to begin mowing.

Disengaging the PTO

1.Set the throttle midway between the “SLOW” and “FAST” positions.

2.Push the PTO switch in to disengage the blades.

Important: To begin movement (forward or backward) the operator must be in the seat, the brake lever must be disengaged (pushed down) before the motion control levers can be moved in or the engine will stop.

When the motion control levers are positioned fully outward (apart) in the T-slot, the drive system is in the neutral lock position (Figure 13).

When the motion control levers are moved directly inward (together) the drive system is in the neutral operate position.

Stopping the Engine

1.Bring the unit to a full stop.

2.Move the motion control levers out to the neutral lock position.

3.Engage the parking brake.

4.Place the throttle midway between the “SLOW” and “FAST” positions.

5.Disengage the PTO.

6.Allow the engine to run for a minimum of 15 seconds, then turn the ignition switch to the “OFF” position to stop the engine.

7.Remove the key to prevent children or other unauthorized persons from starting engine.

8.Close the fuel shut-off valve when the machine will not be in use for a few days, when transporting, or when the unit is parked inside a building.

Driving the Machine

CAUTION

Machine can spin very rapidly by positioning one lever too much ahead of the other. Operator may lose control of the machine, which may cause damage to the machine or injury.

•Use caution when making turns.

•Slow the machine down before making sharp turns.

Figure 13

1.

Neutral lock position

4.

Forward

 

(handles out)

 

 

2.

Neutral operate position

5.

Neutral (operate)

 

(handles in)

 

 

3.

Front of Unit

6.

Reverse

Driving Forward

1.Release the parking brake.

2.Move the motion control levers inward to the center to the neutral position.

3.To move forward in a straight line, move both levers forward with equal pressure.

To turn left or right, pull the motion control lever back toward neutral in the desired turn direction.

The machine will move faster the farther the motion control levers are moved from the neutral position.

4.To stop, position both motion control levers in the neutral operate position.

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Pioneer S-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Systems SpecificationsModel Numbers Cutting Deck DimensionsHydrostatic Ground Drive System Tires & WheelsTorque Requirements Motion Control Levers Product OverviewOperation ControlsHour Meter Ignition Switch Fuel Shut-Off ValveThrottle Control Brake LeverDrive Wheel Release Valves PTO Engagement SwitchTransport Lock Pre-StartOperating Instructions Deck Lift PedalEngaging the PTO Open the Fuel Shut-Off ValveStarting the Engine Driving the Machine Disengaging the PTOStopping the Engine Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightLoading a Unit TransportingTransporting a Unit Operation Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeRecommended Jump Starting Procedure Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltLubricate Caster Wheel Hubs Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Check Spark Arrester if equipped Deck Leveling Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseInch Deck Adjusting the Blade SlopeDeck Belt Tension Adjusting the Parking BrakePump Drive Belt Tension Motion Control Linkage Adjustment Motion Control Handle AdjustmentFull Forward Tracking Adjustment Adjusting the Seat Ride Suspension Removing the Shim Electric Clutch AdjustmentClean Hydro Fan Cooling Fins Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer S-Series Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb

920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents