Exmark 920 manual Transporting a Unit, Loading a Unit

Page 25

Operation

Figure 16

For cutting heights above 3.5 inches (90 mm) use the bottom hole. The rollers will still be effective against scalping.

1. Anti-scalp roller

2. Cutting height

mounting bracket

 

For Maximum Deck Flotation, place the rollers one hole position lower. Rollers should maintain 1/4 inch (6.4 mm) clearance to the ground. Do Not adjust the rollers to support the deck.

Note: The foot operated deck lift lever can be used to momentarily lift the deck to clear objects. Be sure that PTO is disengaged.

7.Torque the 3/8 nyloc nut to 27-33 ft-lb (37-45 N-m).

Figure 17

1.

Wheel bolt

3.

3/8 nyloc-torque to 27-33

 

 

 

ft-lb (37-45 N-m)

2.

Anti-scalp roller

4.

Front right anti-scalp

 

 

 

bracket shown

 

 

 

 

Transporting

Transporting a Unit

Use a heavy-duty trailer or truck to transport the machine. Lock brake and block wheels. Securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes. Be sure that the trailer or truck has all necessary lighting and marking as required by law. Secure a trailer with a safety chain.

CAUTION

This unit does not have proper turn signals, lights, reflective markings, or a slow moving vehicle emblem. Driving on a street or roadway without such equipment is dangerous and can lead to accidents causing personal injury. Driving on a street or roadway without such equipment may also be a violation of State laws and the operator may be subject to traffic tickets and/or fines.

Do Not drive a unit on a public street or roadway.

WARNING

Loading a unit on a trailer or truck increases the possibility of backward tip-over. Backward tip-over could cause serious injury or death.

Use extreme caution when operating a unit on a ramp.

Use only a single, full width ramp; Do Not use individual ramps for each side of the unit.

If individual ramps must be used, use enough ramps to create an unbroken ramp surface wider than the unit.

Do Not exceed a 15° angle between ramp and ground or between ramp and trailer or truck.

Avoid sudden acceleration while driving unit up a ramp to avoid tipping backward.

Avoid sudden deceleration while backing unit down a ramp to avoid tipping backward.

Loading a Unit

Use extreme caution when loading units on trailers or trucks. One full width ramp that is wide enough to extend beyond the rear tires is recommended instead of individual ramps for each side of the unit. The lower rear section of the tractor frame extends back between the rear wheels and serves as a stop for

25

Image 25
Contents Pioneer S-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System DimensionsTires & Wheels Cutting DeckTorque Requirements Operation Product OverviewControls Motion Control LeversThrottle Control Ignition Switch Fuel Shut-Off ValveBrake Lever Hour MeterDrive Wheel Release Valves PTO Engagement SwitchOperating Instructions Pre-StartDeck Lift Pedal Transport LockStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting a Unit TransportingLoading a Unit Operation Recommended Maintenance Schedules MaintenanceRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Knobs Service Air CleanerCheck Seat Belt Check for Loose HardwareLubricate Grease Fittings Check Hydraulic Oil LevelCheck Tire Pressures Lubricate Caster Wheel HubsChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Check Spark Arrester if equipped Copper-Based Anti-seize Thread Locking AdhesivesDielectric Grease Deck LevelingInch Deck Adjusting the Blade SlopePump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Removing the Shim Electric Clutch AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer S-Series Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb

920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.