Exmark 920 Check Rollover Protections Systems Roll Bar Knobs, Check Seat Belt, Change Engine Oil

Page 31

Maintenance

Check Rollover Protections Systems (Roll Bar) Knobs

Service Interval: Before each use or daily

Check that both the mounting hardware and the knobs are in good working condition. Make sure the knobs are fully engaged with the ROPS in the raised position. The upper hoop of the roll bar may need to be pushed forward or pulled rearward to get both knobs fully engaged.

 

Figure 20

1. Engaged

2. Partially engaged — Do

 

Not operate with ROPS

 

in this condition.

 

 

Check Seat Belt

Service Interval: Before each use or daily

Visually inspect seat belt for wear, cuts, and proper operation of retractor and buckle. Replace before operating if damaged.

Check for Loose Hardware

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

Service Air Cleaner

Service Interval: Every 250 hours—Replace the primary air cleaner element — check secondary air cleaner

element; replace if dirty. (May need more often under severe conditions. See the Engine Owner's Manual for additional information.)

Every 500 hours—Replace the secondary air cleaner element (May need more often under severe conditions. See the Engine Owner's Manual for additional information.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.See the Engine Owner's Manual for maintenance instructions.

Change Engine Oil

Service Interval: After the first 5 hours

Every 100 hours/Yearly (whichever comes first) (May need more often under severe conditions.)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Drain oil while engine is warm from operation.

3.The oil drain hose is located on right hand side of engine at the rear. Place pan under machine to catch oil. Remove plug from end of drain hose. Allow oil to drain and replace oil drain plug. Torque plug to 20-24 ft-lb.

4.Replace the oil filter every other oil change. Clean around oil filter and unscrew filter to remove. Before reinstalling new filter, apply a thin coating of Exmark 4–Cycle Premium Engine oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter then tighten filter an additional 1/2 to 3/4 turn.

5.Clean around oil fill cap and remove cap. Fill to specified capacity and replace cap.

6.Use oil recommended in the Check Engine Oil Level section. Do Not overfill. Start the engine and check for leaks.

7.Wipe up any spilled oil from engine deck mounting surfaces.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Pioneer S-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 109-6014 116-1119 107-2102 116-1121 116-3303 116-4465 116-4430 Model Numbers SpecificationsSystems Cutting Deck DimensionsHydrostatic Ground Drive System Tires & WheelsTorque Requirements Motion Control Levers Product OverviewOperation ControlsHour Meter Ignition Switch Fuel Shut-Off ValveThrottle Control Brake LeverDrive Wheel Release Valves PTO Engagement SwitchTransport Lock Pre-StartOperating Instructions Deck Lift PedalStarting the Engine Open the Fuel Shut-Off ValveEngaging the PTO Stopping the Engine Disengaging the PTODriving the Machine Adjusting the Anti-Scalp Rollers Adjusting the Cutting HeightTransporting a Unit TransportingLoading a Unit Operation Recommended Maintenance Schedules MaintenanceRecommended Jump Starting Procedure Check Battery ChargeCheck Engine Oil Level Check Mower Blades Do Not jump start a weak battery if these conditions existService Dealer Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerCheck Rollover Protections Systems Roll Bar Knobs Check Seat BeltLubricate Caster Wheel Hubs Check Hydraulic Oil LevelLubricate Grease Fittings Check Tire PressuresChange Fuel Filter Check Spark PlugsChange Hydraulic System Filter and Fluid Check Spark Arrester if equipped Deck Leveling Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseInch Deck Adjusting the Blade SlopePump Drive Belt Tension Adjusting the Parking BrakeDeck Belt Tension Full Forward Tracking Adjustment Motion Control Handle AdjustmentMotion Control Linkage Adjustment Adjusting the Seat Ride Suspension Removing the Shim Electric Clutch AdjustmentRemove Engine Shrouds and Clean Cooling Fins Clean Engine and Exhaust System AreaClean Hydro Fan Cooling Fins Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingSee Drive Wheel Release Valves section Electrical Diagram SchematicsElectrical Logic Schematic Pioneer S-Series Turf Equipment Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 42.39 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb

920 specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents