Operation Instructions | Exmark MHP3615KA, MHP3614KA, MHP3615KC

		Drive Linkage
	Clevis Pin	Left Side
	Drive	Left Side
	Drive	Shown
	Lever	Reference for
		Reference for
		Position Only
		Neutral
	Hairpin	Lock/Park
		Brake Latch

FIG. 11

DRIVE LEVER HARDWARE LOCATION

d)Adjust brakes by adjusting wingnut on upper end of each brake rod so that when brakes are engaged there is approximately 1/4” of clearance between ends of drive levers and handle grips (See Figure 10)

Note: Adjustment should allow the brakes to be engaged, yet allow the neutral lock/park brake latches to be moved into the park brake position, if not the brake linkages must be adjusted again.

e)Squeeze the drive levers and move both neutral lock/park brake latches into the neutral lock position. Mower should move forward and backward freely, if not, readjust as stated in Sections 3.11c and 3.11d.

3.12Route the long unattached wiring harness lead, up the left hand side of the handle and connect the two terminals (in any order) to the operator presence control switch terminals underneath the control console.

Fasten the lead to the handle with two small wire ties from the bolt bag, one at the upper end of the handle next to the console, and one at the very lower end of the handle where it attaches to the fuel tank support.

3.13If machine is shipped without muffler installed, install muffler with hardware provided.

3.14For Briggs and Stratton Engines install debris guard to top of engine.

3.15Service Engine: Refer to Engine Owner’s Manual.

3.16GREASE UNIT: NOTE: UNIT IS NOT GREASED AT THE FACTORY. Refer to 5.1.13, for locations and grease amounts.

3.17Follow pre-start instructions as outlined in 4.2.

3.18Perform any needed adjustments as outlined in the Adjustment Section.

4.OPERATION INSTRUCTIONS

4.1Controls

4.1.1Operator Presence Control (OPC) Levers: Located on the upper handle assembly directly above the handle grips. When these levers are depressed, the OPC system senses that the operator is in the normal operator's position. When the levers are released, the OPC system senses that the operator has moved from the normal operating position and will kill the engine if either the transmission shift lever is not in the neutral position or the blade clutch is engaged.

4.1.2Drive Levers: Located on each side of the upper handle assembly directly below the handle grips. These levers individually control the clutching action of the wheel drive belts and brakes. When the drive levers are all of the way down, the wheel drive belts engage and the brakes disengage. Squeezing the left or right hand drive lever causes the left hand or right hand wheel to slow down or stop, which makes the machine turn to the left or right respectively.

- 15 -

MHP4815KC, MHP4816BV, MHP3615KA, MHP3615KC, Mhp4816bv, Mhp5216bv, Mhp3614ka, Mhp4814ka, Mhp3615kc, Mhp4815kc, Mhp4817ka, Mhp5217ka, Mhp4815ka, Mhp3615ka specifications

Exmark has long been a leader in the landscaping and turf care industry, and its MHP series of mowers epitomizes dedication to performance, efficiency, and durability. This lineup of models, including MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, MHP5216BV, and others, has garnered attention for its innovative features and robust design.

The MHP4815KC and MHP3615KC are equipped with powerful engines, ensuring that they can handle a variety of terrain and grass types with ease. With reliable cutting decks, these machines deliver a clean, precise cut that leaves lawns looking immaculate. Their advanced blade systems are designed for optimal airflow, which enhances cutting efficiency and finish.

The MHP3614KA and MHP4816BV models showcase versatility, allowing users to customize their mowing experience. These mowers come with various deck sizes and cutting heights, providing the flexibility needed for different mowing conditions. The MHP5216BV stands out with its rugged construction, tailored for heavy-duty use, making it an ideal choice for professional landscapers and homeowners with large yards.

Integrated with modern technologies, these mowers are designed for user comfort and ease of operation. The ergonomic design of the handles, combined with padded grips, reduces user fatigue during long mowing sessions. Additionally, many models feature intuitive control systems that allow for easy maneuverability, further enhancing the mowing experience.

Safety is paramount in the MHP series. Many of these models include features such as automatic blade shut-off when the operator leaves the seat, ensuring that accidents are minimised. The robust frame construction also contributes significantly to the durability and longevity of the mowers, standing up well to the rigors of regular use.

In summary, the Exmark MHP series, including models like MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, and others, provides top-tier performance, versatility, and safety features. With their powerful engines, advanced cutting technologies, ergonomic designs, and a commitment to user safety, these mowers are truly an investment worth considering for both avid gardeners and professional landscapers alike.