Exmark MHP4816BV, MHP3614KA, MHP3615KC, MHP3615KA, MHP4815KC manual Roller may result

Page 33

clearance to ground. Do Not adjust rollers to support the deck. Be sure roller bolts and nuts are installed with the spring disc washer between head of bolt and mounting bracket. Torque to 40-45ft-lbs., or loss of

roller may result.

c)When operating in extremely rough conditions it may be necessary to position the anti-scalp rollers one or two holes higher than described in "b" to prevent damage to the rollers and/or bolt failure(See Figure 14).

NOTE: When anti-scalp rollers are placed in these positions, reduced deck flotation will result.

5.2.2Blade engagement Linkage: Located between the blade engagement lever on the left handle and the left rear corner of the engine deck.

a)Stop engine and remove spark plug wire(s).

b)With blade drive engaged, adjust the linkage length by loosening the locknut on the turnbuckle and adjusting the turnbuckle so that the bolt on the bellcrank and the indicator arm align with each other within 1/16”. See Figure 15. Tighten locknut against turnbuckle.

FIG. 15

BLADE ENGAGEMENT LINKAGE

5.2.3Blade Safety Switch:

a)Stop engine and remove spark plug wire(s).

b)With blades disengaged and the bellcrank touching the rear of the slot in the engine deck, adjust the blade safety switch (if needed) until the bellcrank arm is 5/16” from the switch body.

c)Be sure the bellcrank DOES NOT touch the switch body or damage to the switch could occur.

d)Retighten blade switch mounting hardware.

5.2.4Engine to Cutter Deck Belt: No adjustment necessary.

5.2.5Transmission Belt Adjustment:

a)Stop engine and remove spark plug wire(s).

b)To tighten transmission belt, loosen the 3/8” nyloc nut on transmission belt idler pulley. Slide bolt inward in slot and retighten nyloc nut.

c)When properly adjusted, the belt should have 1/2” of deflection with three pounds of pressure on the belt midway between the transmission and engine pulley.

5.2.6Wheel drive belts and scrapers:

a)If wheel traction appears to be slipping, drive lever rods may be touching bottom of neutral lock/park brake latch slot. To adjust, refer to directions in Section 3.11

NOTE: Wheel drive springs have three tension settings. Refer to Section 5.2.11.

- 28 -

Page 32 Page 34
Image 33
Page 32 Page 34
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Specifications Table of Contents SafetyAssembly Instructions Maintenance & AdjustmentsYour Safety is Involved SafetySafety Alert Symbol TrainingPotential Hazard Operation Maintenance and Storage Riding Attachments Safety SignsPage Page Specifications Dimensions Wheel Drive SystemTires Assembly Instructions Torque RequirementsUpper Handle Mounting 15 & 17 HP Kawasaki Speed Control Throttle Cable HOOK-UP For Kohler engines This Clearance should be Equal Shifter Lever To Transmission Blade Engagement LinkageLever and ROD Adjustment This Clearance should be EqualNeutral Lock Lever Clearance Drive Lever Hardware Location Operation InstructionsDrive LEVER, Neutral LOCK/PARK Brake Latch Operation Pre-Start Operating Instructions Potential Hazard Rotating blades under the mower deck are dangerous Maintenance & Adjustments Periodic MaintenanceTransporting Do not Overfill Blade Bolt Installation Page Fitting Initial Quantity Service Locations Pump Interval Grease Lubrication ChartPivot Point Spray Lubricant ChartAdjustments Roller may result Drive Belt Tension Adjustment Positions Mower Pulling Left or Right Trouble ShootingMower Cuts Unevenly Engine will not StartEngine Troubleshooting Engine Troubleshooting TableProblem Wiring Diagram Page Warranty Page Service Record Page Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care

MHP4815KC, MHP4816BV, MHP3615KA, MHP3615KC, Mhp4816bv, Mhp5216bv, Mhp3614ka, Mhp4814ka, Mhp3615kc, Mhp4815kc, Mhp4817ka, Mhp5217ka, Mhp4815ka, Mhp3615ka specifications

Exmark has long been a leader in the landscaping and turf care industry, and its MHP series of mowers epitomizes dedication to performance, efficiency, and durability. This lineup of models, including MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, MHP5216BV, and others, has garnered attention for its innovative features and robust design.

The MHP4815KC and MHP3615KC are equipped with powerful engines, ensuring that they can handle a variety of terrain and grass types with ease. With reliable cutting decks, these machines deliver a clean, precise cut that leaves lawns looking immaculate. Their advanced blade systems are designed for optimal airflow, which enhances cutting efficiency and finish.

The MHP3614KA and MHP4816BV models showcase versatility, allowing users to customize their mowing experience. These mowers come with various deck sizes and cutting heights, providing the flexibility needed for different mowing conditions. The MHP5216BV stands out with its rugged construction, tailored for heavy-duty use, making it an ideal choice for professional landscapers and homeowners with large yards.

Integrated with modern technologies, these mowers are designed for user comfort and ease of operation. The ergonomic design of the handles, combined with padded grips, reduces user fatigue during long mowing sessions. Additionally, many models feature intuitive control systems that allow for easy maneuverability, further enhancing the mowing experience.

Safety is paramount in the MHP series. Many of these models include features such as automatic blade shut-off when the operator leaves the seat, ensuring that accidents are minimised. The robust frame construction also contributes significantly to the durability and longevity of the mowers, standing up well to the rigors of regular use.

In summary, the Exmark MHP series, including models like MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, and others, provides top-tier performance, versatility, and safety features. With their powerful engines, advanced cutting technologies, ergonomic designs, and a commitment to user safety, these mowers are truly an investment worth considering for both avid gardeners and professional landscapers alike.
Top Page Image Contents