Exmark MHP4815KC, MHP3614KA, MHP3615KC, MHP3615KA, MHP4816BV manual Blade Bolt Installation

Page 28

a)Disengage blade clutch.

b)Stop engine and remove spark plug wire(s).

c)Raise deck and block up using proper safety precautions.

d)Clean out any grass build-up from underside of deck and in deck discharge chute.

e)Inspect blades and sharpen or replace as required.

f)If blade removal is necessary, be careful for the sharp cutting edges of the blades.

g)Re-install the blades (if they were removed) and torque blade bolts to 75- 80 ft. lbs. Be sure the spring disc washer cone is installed toward the bolt head (See Figure 13).

h)Remove jack stands (or equivalent support) and lower deck to ground.

FIG. 13

BLADE BOLT INSTALLATION

5.1.4Check safety interlock system. Service Interval: Daily

a)For your safety, your Exmark mower is equipped with Operator Presence Controls (OPC). When either the mower blades are engaged, or the transmission shift lever is not in neutral and both hands are removed from the handles, the mower engine MUST stop.

b)Check OPC circuits. Clear the area. Run engine at one-third throttle, then with drive levers and neutral lock/park brake latches in “park brake” position, Shift the transmission into gear and release OPC levers – engine MUST stop.

Again, run engine at one-third throttle, move the transmission shifter lever to neutral, engage blade clutch and release OPC levers - engine MUST stop.

c)If machine does not pass any of these tests, DO NOT operate. Contact your authorized EXMARK SERVICE DEALER.

IMPORTANT: It is essential that all Operator Safety Mechanisms, be in place and in proper operating condition prior to mowing.

5.1.5Check for loose hardware. Service Interval: Daily

a)Stop engine and remove spark plug wire(s).

b)Visually inspect machine for any loose hardware or any other possible problem. Tighten hardware or correct the problem before operating.

- 23 -

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety SpecificationsAssembly Instructions Maintenance & AdjustmentsSafety Your Safety is InvolvedSafety Alert Symbol TrainingPotential Hazard Operation Maintenance and Storage Safety Signs Riding AttachmentsPage Page Specifications Wheel Drive System DimensionsTires Torque Requirements Assembly InstructionsUpper Handle Mounting 15 & 17 HP Kawasaki Speed Control Throttle Cable HOOK-UP For Kohler engines Blade Engagement Linkage This Clearance should be Equal Shifter Lever To TransmissionThis Clearance should be Equal Lever and ROD AdjustmentNeutral Lock Lever Clearance Operation Instructions Drive Lever Hardware LocationDrive LEVER, Neutral LOCK/PARK Brake Latch Operation Pre-Start Operating Instructions Potential Hazard Rotating blades under the mower deck are dangerous Periodic Maintenance Maintenance & AdjustmentsTransporting Do not Overfill Blade Bolt Installation Page Grease Lubrication Chart Fitting Initial Quantity Service Locations Pump IntervalSpray Lubricant Chart Pivot PointAdjustments Roller may result Drive Belt Tension Adjustment Positions Trouble Shooting Mower Pulling Left or RightMower Cuts Unevenly Engine will not StartEngine Troubleshooting Table Engine TroubleshootingProblem Wiring Diagram Page Warranty Page Service Record Page Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care

MHP4815KC, MHP4816BV, MHP3615KA, MHP3615KC, Mhp4816bv, Mhp5216bv, Mhp3614ka, Mhp4814ka, Mhp3615kc, Mhp4815kc, Mhp4817ka, Mhp5217ka, Mhp4815ka, Mhp3615ka specifications

Exmark has long been a leader in the landscaping and turf care industry, and its MHP series of mowers epitomizes dedication to performance, efficiency, and durability. This lineup of models, including MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, MHP5216BV, and others, has garnered attention for its innovative features and robust design.

The MHP4815KC and MHP3615KC are equipped with powerful engines, ensuring that they can handle a variety of terrain and grass types with ease. With reliable cutting decks, these machines deliver a clean, precise cut that leaves lawns looking immaculate. Their advanced blade systems are designed for optimal airflow, which enhances cutting efficiency and finish.

The MHP3614KA and MHP4816BV models showcase versatility, allowing users to customize their mowing experience. These mowers come with various deck sizes and cutting heights, providing the flexibility needed for different mowing conditions. The MHP5216BV stands out with its rugged construction, tailored for heavy-duty use, making it an ideal choice for professional landscapers and homeowners with large yards.

Integrated with modern technologies, these mowers are designed for user comfort and ease of operation. The ergonomic design of the handles, combined with padded grips, reduces user fatigue during long mowing sessions. Additionally, many models feature intuitive control systems that allow for easy maneuverability, further enhancing the mowing experience.

Safety is paramount in the MHP series. Many of these models include features such as automatic blade shut-off when the operator leaves the seat, ensuring that accidents are minimised. The robust frame construction also contributes significantly to the durability and longevity of the mowers, standing up well to the rigors of regular use.

In summary, the Exmark MHP series, including models like MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, and others, provides top-tier performance, versatility, and safety features. With their powerful engines, advanced cutting technologies, ergonomic designs, and a commitment to user safety, these mowers are truly an investment worth considering for both avid gardeners and professional landscapers alike.
Top Page Image Contents