Exmark MHP3615KC, MHP3614KA, MHP3615KA, MHP4816BV, MHP4815KC manual Spray Lubricant Chart, Pivot Point

Page 31

No. 5 (Clutch Arm Pivot)

Located Under Engine Deck

No. 7 (Trans. Coupler)

Located Below Fuel Tank Support

No. 4 & 7 (Idler Arm Pivots)

Disassemble and grease once a Month under a “No Load” condition

c) Lubricate pivot points with a spray penetrating lubricant as directed below.

SPRAY LUBRICANT CHART

PIVOT POINT

NO. OF

SERVICE

PLACES

INTERVAL

 

1. Blade Engagement Lever

1

Weekly

d) Lubricate drive wheel hubs once a year. First remove wheel, then remove hub cap. Lubricate the grease fitting on each wheel hub with an SAE No. 2 multipurpose gun grease, until grease appears through outer bearing.

Reinstall hub caps and wheels.

e)Replace 5-speed gearbox grease yearly. Use 18 oz. Of Peerless grease (Part No. 788067). See Section 5.1.9.

5.1.14Check spark plugs. Service Interval: 160 hrs.

a)Remove spark plugs, check condition and adjust plug gap or replace with new plugs. See Engine Owner's Manual.

5.1.15Remove engine shrouds and clean cooling fins. Service Interval: See Engine Owner's Manual

a)Stop engine and remove spark plug wire(s).

b)Remove cooling shrouds from engine and clean cooling fins. Also clean dust, dirt and oil from external surfaces of engine which can cause improper cooling.

c)Make sure cooling shrouds are properly reinstalled. Operating the engine without cooling shrouds will cause engine damage due to overheating.

5.1.16Change fuel filter.

Service Interval: As Required

a)A fuel filter is installed in the fuel line between the fuel tank and the engine. Replace when necessary.

5.1.17Refer to Engine Operators Manual for detailed maintenance regarding the engine.

5.1.18Thread locking adhesives such as “Loctite 242” or “Fel-Pro,Pro-Lock Nut- Type” are used on the following fasteners:

a)Transmission drive sheave setscrew.

b)Wheel drive sheave setscrews on transmission output shafts.

c)OPC lever setscrews.

d)Sheave retaining bolt in end of engine crankshaft.

- 26 -

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Page Potential Hazard Exmark Parts PLUS Program Operators Manual Maintenance & Adjustments Table of Contents SafetySpecifications Assembly InstructionsTraining SafetyYour Safety is Involved Safety Alert SymbolPotential Hazard Operation Maintenance and Storage Riding Attachments Safety SignsPage Page Specifications Wheel Drive System DimensionsTires Torque Requirements Assembly InstructionsUpper Handle Mounting 15 & 17 HP Kawasaki Speed Control Throttle Cable HOOK-UP For Kohler engines This Clearance should be Equal Shifter Lever To Transmission Blade Engagement LinkageThis Clearance should be Equal Lever and ROD AdjustmentNeutral Lock Lever Clearance Drive Lever Hardware Location Operation InstructionsDrive LEVER, Neutral LOCK/PARK Brake Latch Operation Pre-Start Operating Instructions Potential Hazard Rotating blades under the mower deck are dangerous Periodic Maintenance Maintenance & AdjustmentsTransporting Do not Overfill Blade Bolt Installation Page Fitting Initial Quantity Service Locations Pump Interval Grease Lubrication ChartPivot Point Spray Lubricant ChartAdjustments Roller may result Drive Belt Tension Adjustment Positions Engine will not Start Trouble ShootingMower Pulling Left or Right Mower Cuts UnevenlyEngine Troubleshooting Table Engine TroubleshootingProblem Wiring Diagram Page Warranty Page Service Record Page Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care

MHP4815KC, MHP4816BV, MHP3615KA, MHP3615KC, Mhp4816bv, Mhp5216bv, Mhp3614ka, Mhp4814ka, Mhp3615kc, Mhp4815kc, Mhp4817ka, Mhp5217ka, Mhp4815ka, Mhp3615ka specifications

Exmark has long been a leader in the landscaping and turf care industry, and its MHP series of mowers epitomizes dedication to performance, efficiency, and durability. This lineup of models, including MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, MHP5216BV, and others, has garnered attention for its innovative features and robust design.

The MHP4815KC and MHP3615KC are equipped with powerful engines, ensuring that they can handle a variety of terrain and grass types with ease. With reliable cutting decks, these machines deliver a clean, precise cut that leaves lawns looking immaculate. Their advanced blade systems are designed for optimal airflow, which enhances cutting efficiency and finish.

The MHP3614KA and MHP4816BV models showcase versatility, allowing users to customize their mowing experience. These mowers come with various deck sizes and cutting heights, providing the flexibility needed for different mowing conditions. The MHP5216BV stands out with its rugged construction, tailored for heavy-duty use, making it an ideal choice for professional landscapers and homeowners with large yards.

Integrated with modern technologies, these mowers are designed for user comfort and ease of operation. The ergonomic design of the handles, combined with padded grips, reduces user fatigue during long mowing sessions. Additionally, many models feature intuitive control systems that allow for easy maneuverability, further enhancing the mowing experience.

Safety is paramount in the MHP series. Many of these models include features such as automatic blade shut-off when the operator leaves the seat, ensuring that accidents are minimised. The robust frame construction also contributes significantly to the durability and longevity of the mowers, standing up well to the rigors of regular use.

In summary, the Exmark MHP series, including models like MHP4815KC, MHP3615KC, MHP3614KA, MHP4816BV, and others, provides top-tier performance, versatility, and safety features. With their powerful engines, advanced cutting technologies, ergonomic designs, and a commitment to user safety, these mowers are truly an investment worth considering for both avid gardeners and professional landscapers alike.
Top Page Image Contents