Exmark 4500-759 Rev A manual Operating the Machine with the Platform Up

Page 23

Operation

WARNING

The operator platform is heavy and may cause injury when lowering and raising the operator platform. The platform may suddenly drop if not supported when the latch pin is pulled out.

•Do Not put your hands or fingers in the platform pivot area when lowering or raising the operator platform.

•Make sure the platform is supported when the latch pin is pulled out.

•Make sure the latch secures the platform when folding it in the up position. Push it tight against the cushion for the latch pin to lock into place.

Figure 12

1.Platform

2.Raise upward

3.Latch pin knob snaps inward

Operating the Machine with the Platform Up

Operating the machine with the platform up is recommended when:

•Mowing near drop-off ’s

•Mowing small areas where the machine is too long

•Areas with low over hanging branches or obstacles

•Loading the machine for transport

•Unloading the machine after transport

•Driving up or backing down slopes or ramps.

•Turning in tight areas where platform may contact obstacles.

To raise the platform, pull the bottom upward and push it tight against the cushion. The latch pin knob will snap inward to lock the platform into place (see Figure 12).

Operating the Machine with the Platform Down

Operating the machine with the platform down is recommended when:

•Mowing most areas

•Driving down slopes

To lower the platform, push the platform forward against the cushion to release pressure on the latch pin, pull the knob outward, and lower the platform (see Figure 13).

Figure 13

1.Pull latch pin knob outward

2.Platform

3.Lower

23

Page 22 Page 24
Image 23
Page 22 Page 24
Contents Vantage California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3267 116-3283 116-3290 116-1887 116-4181 116-4647 116-5040 EFI Only Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationFuel Gauge Ignition Switch Hour MeterFuel Shut-Off Valve Operating Instructions Pre-StartStopping the Engine PTO EngagementDisengaging the PTO Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting a Unit Adjusting the Cutting HeightTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Release the Cushion for Rear AccessSafety interlock system is designed to stop Check Safety Interlock SystemCheck Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationDielectric Grease Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeAdjusting the Cutting Deck Rake Mower Deck Drive Belt Tension Adjusting the Rear of the DeckPark Brake Adjustment Pump Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Debris From Machine Clean Engine and Exhaust System AreaClean Grass Build-Up Under Deck Remove Engine Shrouds and Clean Cooling FinsMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-759 Rev A specifications

The Exmark 4500-759 Rev A represents an innovative leap in turf management equipment, designed to enhance the efficiency and effectiveness of landscaping professionals. As a leading name in the lawn care industry, Exmark has equipped this model with state-of-the-art technologies and features that cater to both commercial and residential users.

One of the standout characteristics of the Exmark 4500-759 Rev A is its robust engine performance. Powered by a high-efficiency engine, it delivers consistent power and torque, allowing for seamless operation across diverse terrains. This engine is complemented by advanced cooling systems, ensuring optimal temperature management during extended use, which ultimately prolongs the equipment's lifespan.

The cutting system on the 4500-759 Rev A is another highlight, featuring Exmark’s patented cutting deck design. The advanced blade and deck configuration promotes superior grass dispersion and minimizes clumping, resulting in a polished finish that landscapers strive to achieve. The adjustable cutting height feature allows users to tailor the lawn height to their preference, making it versatile for various types of grass and seasonal conditions.

Operator comfort and ease of use are paramount in the design of the Exmark 4500-759 Rev A. The ergonomically designed seat and user-friendly controls provide a smooth driving experience. The intuitive dashboard offers easy access to critical information about the mower’s operation, ensuring that operators can focus on the task at hand without any distractions.

Additionally, this model incorporates innovative technology with its integrated GPS tracking system, which enhances efficiency by allowing users to monitor location and performance remotely. This feature not only aids in job tracking but also supports maintenance scheduling, optimizing service intervals and reducing downtime.

Furthermore, the Exmark 4500-759 Rev A is built with durability in mind. The heavy-duty frame and reinforced components withstand rigorous use, ensuring long-lasting performance in demanding environments. The model's versatility enables it to adapt for various landscaping tasks, from mowing to mulching, making it a valuable tool for professionals.

In conclusion, the Exmark 4500-759 Rev A is a powerful and versatile mower equipped with advanced technologies that simplify lawn care while maximizing results. Its combination of performance, comfort, and durability positions it as an essential choice for those in the landscaping industry, empowering users to achieve their desired outcomes with confidence.
Top Page Image Contents