Exmark 4500-759 Rev A manual Wheel Hub Nut Torque Specification, Check Spark Arrester if equipped

Page 35

Maintenance

Figure 21

1. Charge pump cap

2. Loosen 1 1/2 turns only

1.Stop engine and wait for all moving parts to stop. Raise the rear of the machine up onto jack stands high enough to raise the drive wheels off the ground.

2.Check oil level as stated in Check Hydraulic Oil Level section.

3.Start engine and move throttle control ahead to full throttle position. Move RH motion control lever inward (together) and move both levers forward with equal pressure.

If either drive wheel does not rotate, it is possible to assist the purging of the charge pump by carefully rotating the tire in the forward position.

Note: It is necessary to lightly touch the charge pump cap with your hand to check the pump temperature. If the cap is too hot to touch, turn off engine. The pumps may be damaged if the pump becomes too hot.

If either drive wheel still does not rotate continue with step 4.

4.Thoroughly clean the area around each of the charge pump housings.

5.To “prime” charge pump, loosen two hex socket head capscrews (shown in Figure 21) 1 1/2 turns only. Make sure engine is not running. Lift the charge pump housing upward and wait for a steady flow of oil to flow out from under the housing. Retighten the capscrews. Do this for both pumps.

Note: Hydraulic reservoir can be pressurized up to 5 psi to speed this process.

6.If either drive wheel still does not rotate, stop and repeat steps 4 and 5 above for the respective

pump. If wheels rotate slowly, the system may prime after additional running. Check oil level as stated in Check the Hydraulic Oil Level section.

7.Allow unit to run several minutes after the charge pumps are “primed” with drive system in the full speed position. Check oil level as stated in Check the Hydraulic Oil Level section.

8.Check hydro drive linkage adjustment as stated in Hydro Drive Linkage Adjustment section in Adjustments.

Wheel Hub Nut Torque Specification

Service Interval: After the first 100 hours

Every 500 hours thereafter

Torque the nut on the wheel motor tapered shaft to 175-225 ft-lb (237-305 N-m).

Note: Do Not use anti-seize compound on the wheel hub.

Check Spark Arrester (if equipped)

Service Interval: Every 50 hours

WARNING

Hot exhaust system components may ignite gasoline vapors even after the engine is stopped. Hot particles exhausted during engine operation may ignite flammable materials. Fire may result in personal injury or property damage.

Do Not refuel or run engine unless spark arrester is installed.

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Wait for muffler to cool.

3.If any breaks in the screen or welds are observed, replace arrester.

4.If plugging of the screen is observed, remove arrester and shake loose particles out of the arrester and clean screen with a wire brush (soak in solvent if necessary). Reinstall arrester on exhaust outlet.

35

Image 35
Contents Vantage California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3267 116-3283 116-3290 116-1887 116-4181 116-4647 116-5040 EFI Only Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationFuel Gauge Ignition Switch Hour MeterFuel Shut-Off Valve Operating Instructions Pre-StartStopping the Engine PTO EngagementDisengaging the PTO Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting a Unit Adjusting the Cutting HeightTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Release the Cushion for Rear AccessSafety interlock system is designed to stop Check Safety Interlock SystemCheck Hydraulic Oil Level Service Air CleanerCheck for Loose Hardware Change Engine OilLubricate Caster Wheel Hubs Check Tire PressuresCheck Condition Of Belts Lubricate Grease FittingsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationDielectric Grease Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeAdjusting the Cutting Deck Rake Mower Deck Drive Belt Tension Adjusting the Rear of the DeckPark Brake Adjustment Pump Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Debris From Machine Clean Engine and Exhaust System AreaClean Grass Build-Up Under Deck Remove Engine Shrouds and Clean Cooling FinsMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-759 Rev A specifications

The Exmark 4500-759 Rev A represents an innovative leap in turf management equipment, designed to enhance the efficiency and effectiveness of landscaping professionals. As a leading name in the lawn care industry, Exmark has equipped this model with state-of-the-art technologies and features that cater to both commercial and residential users.

One of the standout characteristics of the Exmark 4500-759 Rev A is its robust engine performance. Powered by a high-efficiency engine, it delivers consistent power and torque, allowing for seamless operation across diverse terrains. This engine is complemented by advanced cooling systems, ensuring optimal temperature management during extended use, which ultimately prolongs the equipment's lifespan.

The cutting system on the 4500-759 Rev A is another highlight, featuring Exmark’s patented cutting deck design. The advanced blade and deck configuration promotes superior grass dispersion and minimizes clumping, resulting in a polished finish that landscapers strive to achieve. The adjustable cutting height feature allows users to tailor the lawn height to their preference, making it versatile for various types of grass and seasonal conditions.

Operator comfort and ease of use are paramount in the design of the Exmark 4500-759 Rev A. The ergonomically designed seat and user-friendly controls provide a smooth driving experience. The intuitive dashboard offers easy access to critical information about the mower’s operation, ensuring that operators can focus on the task at hand without any distractions.

Additionally, this model incorporates innovative technology with its integrated GPS tracking system, which enhances efficiency by allowing users to monitor location and performance remotely. This feature not only aids in job tracking but also supports maintenance scheduling, optimizing service intervals and reducing downtime.

Furthermore, the Exmark 4500-759 Rev A is built with durability in mind. The heavy-duty frame and reinforced components withstand rigorous use, ensuring long-lasting performance in demanding environments. The model's versatility enables it to adapt for various landscaping tasks, from mowing to mulching, making it a valuable tool for professionals.

In conclusion, the Exmark 4500-759 Rev A is a powerful and versatile mower equipped with advanced technologies that simplify lawn care while maximizing results. Its combination of performance, comfort, and durability positions it as an essential choice for those in the landscaping industry, empowering users to achieve their desired outcomes with confidence.