Exmark 4500-759 Rev A manual Release the Cushion for Rear Access, Check Mower Blades

Page 29

Maintenance

4.Connect the other end of the positive cable to the positive terminal of the booster battery.

5.Connect the black negative (–) cable to the other terminal (negative) of the booster battery.

6.MAKE THE FINAL CONNECTION ON THE ENGINE BLOCK OF THE STALLED VEHICLE (NOT TO THE NEGATIVE POST) AWAY FROM THE BATTERY. STAND BACK.

7.Start the vehicle and remove the cables in the reverse order of connection (the engine block (black) connection is the first to disconnect).

Release the Cushion for Rear Access

Service Interval: As required

The cushion can be released for rear access to the machine for maintenance or adjustment.

1.Lower the platform.

2.Remove the hairpins on each side of the cushion.

3.Push the plastic slides to the inside.

4.Remove the cushion and lower it to the platform.

5.Perform any maintenance or adjustment on the machine.

6.Raise the cushion and slide it onto the pins on both sides of the machine (Figure 17).

7.Push the plastic slides into the cushion bracket and secure them with a hairpin.

Figure 17

1.Plastic slide

2.Cushion bracket with key hole

3.Hairpin

Check Mower Blades

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck section.

3.Inspect blades and sharpen or replace as required.

4.Reinstall the blades (if they were removed) in the following order:

A.Install bushing through blade with bushing flange on bottom (grass) side of blade.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Vantage California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3267 116-3283 116-3290 116-1887 116-4181 116-4647 116-5040 EFI Only Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationFuel Gauge Ignition Switch Hour MeterFuel Shut-Off Valve Operating Instructions Pre-StartStopping the Engine PTO EngagementDisengaging the PTO Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting a Unit Adjusting the Cutting HeightTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Release the Cushion for Rear AccessSafety interlock system is designed to stop Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationMobil HTS Grease Or Food-Grade Anti-seize Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjusting the Cutting Deck Rake Park Brake Adjustment Adjusting the Rear of the DeckPump Drive Belt Tension Mower Deck Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-759 Rev A specifications

The Exmark 4500-759 Rev A represents an innovative leap in turf management equipment, designed to enhance the efficiency and effectiveness of landscaping professionals. As a leading name in the lawn care industry, Exmark has equipped this model with state-of-the-art technologies and features that cater to both commercial and residential users.

One of the standout characteristics of the Exmark 4500-759 Rev A is its robust engine performance. Powered by a high-efficiency engine, it delivers consistent power and torque, allowing for seamless operation across diverse terrains. This engine is complemented by advanced cooling systems, ensuring optimal temperature management during extended use, which ultimately prolongs the equipment's lifespan.

The cutting system on the 4500-759 Rev A is another highlight, featuring Exmark’s patented cutting deck design. The advanced blade and deck configuration promotes superior grass dispersion and minimizes clumping, resulting in a polished finish that landscapers strive to achieve. The adjustable cutting height feature allows users to tailor the lawn height to their preference, making it versatile for various types of grass and seasonal conditions.

Operator comfort and ease of use are paramount in the design of the Exmark 4500-759 Rev A. The ergonomically designed seat and user-friendly controls provide a smooth driving experience. The intuitive dashboard offers easy access to critical information about the mower’s operation, ensuring that operators can focus on the task at hand without any distractions.

Additionally, this model incorporates innovative technology with its integrated GPS tracking system, which enhances efficiency by allowing users to monitor location and performance remotely. This feature not only aids in job tracking but also supports maintenance scheduling, optimizing service intervals and reducing downtime.

Furthermore, the Exmark 4500-759 Rev A is built with durability in mind. The heavy-duty frame and reinforced components withstand rigorous use, ensuring long-lasting performance in demanding environments. The model's versatility enables it to adapt for various landscaping tasks, from mowing to mulching, making it a valuable tool for professionals.

In conclusion, the Exmark 4500-759 Rev A is a powerful and versatile mower equipped with advanced technologies that simplify lawn care while maximizing results. Its combination of performance, comfort, and durability positions it as an essential choice for those in the landscaping industry, empowering users to achieve their desired outcomes with confidence.
Top Page Image Contents