Exmark 4500-759 Rev A manual Adjusting the Cutting Height, Transporting a Unit

Page 24

Operation

Adjusting the Cutting Height

The cutting height of the mower deck is adjusted from 1 to 5 inches (2.5 cm to 12.7 cm) in 1/4 inch (6.4 mm) increments.

1.Stop the machine and move the motion control levers to the neutral position.

2.Disengage the PTO.

3.Raise and lock the deck to the 5 inch (12.7 cm) transport position.

The deck is raised by pulling the deck lift handle rearward and to the right to place it into the transport lock position.

Figure 15

1.

Height adjustment pin

3. Deck lift handle

2.

Height of cut holes

 

 

 

 

Figure 14

1.

Transport lock position

3.

Front reference/speed

2.

RH Motion control lever

 

control bar

4.

Deck lift handle

Note: When changing the cutting height positions, always come to a complete stop and disengage the PTO.

4.Insert the height adjustment pin into the hole corresponding to the desired cutting height.

See the decal on the side of the deck lift plate for cut heights (reference Figure 15).

5.Pull the deck lift handle rearward and to the left and slowly allow the deck to lower to the cutting height.

Transporting

Transporting a Unit

Use a heavy-duty trailer or truck to transport the machine. Lock brake and block wheels. Securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes. Be sure that the trailer or truck has all necessary lighting and marking as required by law. Secure a trailer with a safety chain.

CAUTION

This unit does not have proper turn signals, lights, reflective markings, or a slow moving vehicle emblem. Driving on a street or roadway without such equipment is dangerous and can lead to accidents causing personal injury. Driving on a street or roadway without such equipment may also be a violation of State laws and the operator may be subject to traffic tickets and/or fines.

Do Not drive a unit on a public street or roadway.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Vantage California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingSafety Operation Slope OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3267 116-3283 116-3290 116-1887 116-4181 116-4647 116-5040 EFI Only Specifications Model NumbersSystems Dimensions Product Overview Torque RequirementsOperation ControlsIgnition Switch Hour Meter Fuel Shut-Off ValveFuel Gauge Pre-Start Operating InstructionsPTO Engagement Disengaging the PTOStopping the Engine Driving the Machine Driving ForwardAdjusting the Front Reference/Speed Control Bar Operating the PlatformOperating the Machine with the Platform Up Operating the Machine with the Platform DownAdjusting the Cutting Height TransportingTransporting a Unit Loading a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Do Not jump start a weak battery if these conditions existRelease the Cushion for Rear Access Check Mower BladesCheck Safety Interlock System Safety interlock system is designed to stopService Air Cleaner Check for Loose HardwareChange Engine Oil Check Hydraulic Oil LevelCheck Tire Pressures Check Condition Of BeltsLubricate Grease Fittings Lubricate Caster Wheel HubsCheck Spark Plugs Change Fuel FilterChange Hydraulic System Filter and Fluid Hydraulic System Air Purge LevelWheel Hub Nut Torque Specification Check Spark Arrester if equippedThread Locking Adhesives Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreaseAdjusting the Cutting Deck Rake Adjusting the Rear of the Deck Park Brake AdjustmentPump Drive Belt Tension Mower Deck Drive Belt TensionChecking the Tire Pressure in Drive System Electric Clutch Adjustment Removing the ShimMotion Control Neutral Adjustment Motion Control Tracking Adjustment Check the Neutral Switch AlignmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Engine and Exhaust System Area Clean Grass Build-Up Under DeckRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMaintenance Troubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical Diagram-All Units Except Kohler EFIElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-759 Rev A specifications

The Exmark 4500-759 Rev A represents an innovative leap in turf management equipment, designed to enhance the efficiency and effectiveness of landscaping professionals. As a leading name in the lawn care industry, Exmark has equipped this model with state-of-the-art technologies and features that cater to both commercial and residential users.

One of the standout characteristics of the Exmark 4500-759 Rev A is its robust engine performance. Powered by a high-efficiency engine, it delivers consistent power and torque, allowing for seamless operation across diverse terrains. This engine is complemented by advanced cooling systems, ensuring optimal temperature management during extended use, which ultimately prolongs the equipment's lifespan.

The cutting system on the 4500-759 Rev A is another highlight, featuring Exmark’s patented cutting deck design. The advanced blade and deck configuration promotes superior grass dispersion and minimizes clumping, resulting in a polished finish that landscapers strive to achieve. The adjustable cutting height feature allows users to tailor the lawn height to their preference, making it versatile for various types of grass and seasonal conditions.

Operator comfort and ease of use are paramount in the design of the Exmark 4500-759 Rev A. The ergonomically designed seat and user-friendly controls provide a smooth driving experience. The intuitive dashboard offers easy access to critical information about the mower’s operation, ensuring that operators can focus on the task at hand without any distractions.

Additionally, this model incorporates innovative technology with its integrated GPS tracking system, which enhances efficiency by allowing users to monitor location and performance remotely. This feature not only aids in job tracking but also supports maintenance scheduling, optimizing service intervals and reducing downtime.

Furthermore, the Exmark 4500-759 Rev A is built with durability in mind. The heavy-duty frame and reinforced components withstand rigorous use, ensuring long-lasting performance in demanding environments. The model's versatility enables it to adapt for various landscaping tasks, from mowing to mulching, making it a valuable tool for professionals.

In conclusion, the Exmark 4500-759 Rev A is a powerful and versatile mower equipped with advanced technologies that simplify lawn care while maximizing results. Its combination of performance, comfort, and durability positions it as an essential choice for those in the landscaping industry, empowering users to achieve their desired outcomes with confidence.
Top Page Image Contents