Exmark 4500-759 Rev A manual Motion Control Neutral Adjustment

Page 41

Maintenance

G011733

1

Figure 34

1.Feeler gauge

Figure 35

1.Feeler gauge

•If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section.

•If the gap is sufficient, proceed to the safety check in step F.

F.Perform the following safety check:

a.Sit on the seat and start the engine.

b.Make sure the blades Do Not engage with the PTO switch “off ” and the clutch disengaged.

If the clutch does not disengage, reinstall the shim and reference the Troubleshooting section.

c.Engage and disengage the PTO switch ten consecutive times to ensure the clutch is functioning properly. If the clutch does not engage properly, reference the Troubleshooting section.

Motion Control Neutral Adjustment

Check to see if an adjustment is required:

1.With the engine off, turn the ignition switch to the “ON” position.

2.Locate the LCD indicator in the message display.

Figure 36

1.Neutral LCD indicator

3.With the motion control levers in the neutral position (see Figure 4) (with no force on the lever either forward or back), the neutral LCD indicator should appear.

4.If the indicator illuminates, move the RH lever first forward, then backward, noting the position of the control lever when the indicator disappears. The amount of movement, both forward and back, should be approximately the same; if not, go to step 6.

5.If the indicator does not illuminate, move both motion control levers forward and then backward. Continue to watch the message display and note the position of the controls when it appears.

6.Loosen the lock nuts on the RH motion control linkage (as viewed from the rear of the machine

— see Figure 37). With the right motion control in the PTO disengage position, hold the LH motion control in the position determined in step 4 or 5. Rotate the adjustment rod until the LCD indicator comes on.

41

Page 40 Page 42
Image 41
Page 40 Page 42
Contents Vantage California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingSafety Slope Operation OperationMaintenance and Storage Safety Safety and Instructional Decals 116-0404 116-2040 116-3267 116-3283 116-3290 116-1887 116-4181 116-4647 116-5040 EFI Only Systems SpecificationsModel Numbers Dimensions Torque Requirements Product OverviewControls OperationFuel Gauge Ignition Switch Hour MeterFuel Shut-Off Valve Operating Instructions Pre-StartStopping the Engine PTO EngagementDisengaging the PTO Driving Forward Driving the MachineOperating the Platform Adjusting the Front Reference/Speed Control BarOperating the Machine with the Platform Down Operating the Machine with the Platform UpTransporting a Unit Adjusting the Cutting HeightTransporting Loading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeDo Not jump start a weak battery if these conditions exist Recommended Jump Starting ProcedureCheck Mower Blades Release the Cushion for Rear AccessSafety interlock system is designed to stop Check Safety Interlock SystemCheck for Loose Hardware Service Air CleanerChange Engine Oil Check Hydraulic Oil LevelCheck Condition Of Belts Check Tire PressuresLubricate Grease Fittings Lubricate Caster Wheel HubsChange Hydraulic System Filter and Fluid Check Spark PlugsChange Fuel Filter Level Hydraulic System Air PurgeCheck Spark Arrester if equipped Wheel Hub Nut Torque SpecificationMobil HTS Grease Or Food-Grade Anti-seize Thread Locking AdhesivesCopper-Based Anti-seize Dielectric GreaseAdjusting the Cutting Deck Rake Park Brake Adjustment Adjusting the Rear of the DeckPump Drive Belt Tension Mower Deck Drive Belt TensionChecking the Tire Pressure in Drive System Removing the Shim Electric Clutch AdjustmentMotion Control Neutral Adjustment Check the Neutral Switch Alignment Motion Control Tracking AdjustmentAdjust RH Motion Control Handle Position Caster Pivot Bearings Pre-Load Adjustment Clean Grass Build-Up Under Deck Clean Engine and Exhaust System AreaRemove Engine Shrouds and Clean Cooling Fins Clean Debris From MachineMaintenance Problem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram-All Units Except Kohler EFI SchematicsElectrical Diagram-Kohler EFI Electrical Schematic-All Units Except Kohler EFI Electrical Schematic-Kohler EFI Hydraulic Diagram General Warranty Conditions and Products Covered Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options

4500-759 Rev A specifications

The Exmark 4500-759 Rev A represents an innovative leap in turf management equipment, designed to enhance the efficiency and effectiveness of landscaping professionals. As a leading name in the lawn care industry, Exmark has equipped this model with state-of-the-art technologies and features that cater to both commercial and residential users.

One of the standout characteristics of the Exmark 4500-759 Rev A is its robust engine performance. Powered by a high-efficiency engine, it delivers consistent power and torque, allowing for seamless operation across diverse terrains. This engine is complemented by advanced cooling systems, ensuring optimal temperature management during extended use, which ultimately prolongs the equipment's lifespan.

The cutting system on the 4500-759 Rev A is another highlight, featuring Exmark’s patented cutting deck design. The advanced blade and deck configuration promotes superior grass dispersion and minimizes clumping, resulting in a polished finish that landscapers strive to achieve. The adjustable cutting height feature allows users to tailor the lawn height to their preference, making it versatile for various types of grass and seasonal conditions.

Operator comfort and ease of use are paramount in the design of the Exmark 4500-759 Rev A. The ergonomically designed seat and user-friendly controls provide a smooth driving experience. The intuitive dashboard offers easy access to critical information about the mower’s operation, ensuring that operators can focus on the task at hand without any distractions.

Additionally, this model incorporates innovative technology with its integrated GPS tracking system, which enhances efficiency by allowing users to monitor location and performance remotely. This feature not only aids in job tracking but also supports maintenance scheduling, optimizing service intervals and reducing downtime.

Furthermore, the Exmark 4500-759 Rev A is built with durability in mind. The heavy-duty frame and reinforced components withstand rigorous use, ensuring long-lasting performance in demanding environments. The model's versatility enables it to adapt for various landscaping tasks, from mowing to mulching, making it a valuable tool for professionals.

In conclusion, the Exmark 4500-759 Rev A is a powerful and versatile mower equipped with advanced technologies that simplify lawn care while maximizing results. Its combination of performance, comfort, and durability positions it as an essential choice for those in the landscaping industry, empowering users to achieve their desired outcomes with confidence.
Top Page Image Contents