Exmark 920, 000 & higher manual Check Mower Blades, Engine Block of the Stalled

Page 31

Maintenance

Figure 12

1.Positive (+) cable on discharged battery

2.Positive (+) cable on booster battery

3.Negative (–) cable on the booster battery

4.Negative (–) cable on the engine block

5.Booster battery

6.Discharged battery

7.Engine block

Figure 13

1.Install bushing in blade prior to installing bushing in spindle.

B.Install bushing/blade assembly into spindle.

4.

Connect the other end of the positive cable to the

 

positive terminal of the booster battery.

5.

Connect the black negative (–) cable to the other

 

terminal (negative) of the booster battery.

6.

MAKE THE FINAL CONNECTION ON

 

THE ENGINE BLOCK OF THE STALLED

 

VEHICLE (NOT TO THE NEGATIVE POST)

Figure 14

AWAY FROM THE BATTERY. STAND BACK.

7. Start the vehicle and remove the cables in the

reverse order of connection (the engine block

(black) connection is the first to disconnect).

Check Mower Blades

1.Use wrench here for blade installation. This nut has been torqued to 90–110 ft-lb (122–149 N-m)

2.Torque to 55-60 ft-lb (75-81 N-m) Apply lubricant to threads as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute.

Service Interval: Before each use or daily

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Lift deck and secure in raised position as stated in the Clean Grass Build-Up Under Deck procedure.

3.Inspect blades and sharpen or replace as required.

4.Reinstall the blades (if they were removed) in the following order:

A.Install bushing through blade with bushing flange on bottom (grass) side of blade.

C.Apply lubricant to threads of blade bolt as needed to prevent seizing. Copper-based anti-seize preferable. Grease acceptable substitute. Install blade bolt finger tight. Place wrench on the top spindle nut then torque the blade bolts to 55-60 ft-lb (75-81 N-m).

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Lazer Z D-SERIES California Introduction Contents Training SafetySafety Alert Symbol Safe Operating PracticesOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Model Numbers SpecificationsSystems Cutting Deck SeatHydrostatic Ground Drive System Tires & WheelsTorque Requirements DimensionsMotion Control Levers Product OverviewOperation ControlsHour Meter Ignition SwitchTracking Adjustment Knob Brake LeverPre-Start Open the Fuel Shut-Off Valve Operating InstructionsBiodiesel Ready Raise the Rollover Protection System RopsDisengaging the PTO Engaging the PTOStopping the Engine Driving the Machine Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeService Interval As required Recommended Jump Starting ProcedureEngine Block of the Stalled Check Mower BladesCheck Seat Belt Check Safety Interlock SystemCheck Rollover Protections Systems Roll Bar Pins Service Air CleanerCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Lubricate Grease Fittings Check Condition Of BeltsLubricate Brake Rod Bushings Wheel Hub Slotted Nut Torque SpecificationLubricate Caster Wheel Hubs Lubricate Brake Handle PivotChange Inline Fuel Filter Lubricate Motion Control Bronze BushingsDrain Fuel Filter/Water Separator Change Fuel Filter/Water SeparatorChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedDeck Leveling Mobil HTS Grease Or Food-Grade Anti-seizeCopper-Based Anti-seize Dielectric GreasePump Drive Belt Tension Mule Drive Belt Tension AdjustmentDeck Belt Tension Parking Brake Adjustment Belt Guide AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean Engine and Exhaust System Area Clean Engine Cooling SystemClean the Radiator Waste Disposal Clean Debris From MachineClean Grass Build-Up Under Deck Battery DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.
Top Page Image Contents