Exmark 920, 000 & higher manual Check Engine Coolant Level, Change Engine Coolant

Page 37

Maintenance

6.Raise the rear of machine up and support with jack stands (or equivalent support) just high enough to allow drive wheels to turn freely.

7.Start engine and move throttle control ahead to full throttle position. Move the speed control levers to the full speed and run for several minutes. Shut down machine and recheck oil level.

Note: Do Not change hydraulic system oil (except for what can be drained when changing filter), unless it is felt the oil has been contaminated or been extremely hot.

Changing oil unnecessarily could damage hydraulic system by introducing contaminates into the system.

Check Engine Coolant Level

Service Interval: Before each use or daily

Note: If the engine coolant level is below the indicator line on the overflow bottle when the engine is cold, the coolant temperature gauge may not register correctly during operation and/or the warning buzzer may not sound if the engine overheats.

1.Stop engine and wait for all moving parts to stop. Make sure unit is on a level surface.

2.Check with engine cold.

3.View coolant level in overflow bottle on the left side of the engine compartment. Coolant level should be at the indicator line on the overflow bottle.

4.If the coolant level is low, open hood or raise radiator, remove the cap to the overflow bottle and fill to the indicator line. Units should only be filled with a 50/50 mix of Dex-Cool© extended life coolant and water. Dex-Cool© can be identified by its orange color.

WARNING

Engine coolant is hot and pressurized and radiator and surrounding parts are hot. Spray or steam from hot, pressurized liquid in the engine cooling system and touching a hot radiator may cause severe burns.

Allow the engine to cool completely before removing the radiator cap or servicing any component of the cooling system.

CAUTION

Engine coolant is toxic. Swallowing coolant can cause poisoning.

Do Not swallow.

Keep out of reach of children and pets.

Change Engine Coolant

Service Interval: Every 4,000 hours/Every 4 years (whichever comes first) Dex-Cool©extended life coolant (orange color)

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake. Machine must be positioned on level surface.

2.Unhook seat latch, tilt seat up and tilt hood forward to gain access to the cooling area. Do Not raise radiator, as it may not fully drain in that position.

WARNING

Engine coolant is hot and pressurized and radiator and surrounding parts are hot. Spray or steam from hot, pressurized liquid in the engine cooling system and touching a hot radiator may cause severe burns.

Allow the engine to cool completely before removing the radiator cap or servicing any component of the cooling system.

CAUTION

Engine coolant is toxic. Swallowing coolant can cause poisoning.

Do Not swallow.

Keep out of reach of children and pets.

3.Drain coolant when engine is cool. Coolant may be drained from the radiator by removing the drain plug in the right rear corner. The engine block may be drained by removing the rear radiator hose and/or by opening the drain cock on the right-hand side of the engine block (see Figure 16).

37

Image 37
Contents Lazer Z D-SERIES California Introduction Contents Safety Alert Symbol SafetySafe Operating Practices TrainingOperation Slope Operation Maintenance and Storage Using the Rollover Protection System RopsSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Model Numbers SpecificationsSystems Hydrostatic Ground Drive System SeatTires & Wheels Cutting DeckTorque Requirements DimensionsOperation Product OverviewControls Motion Control LeversTracking Adjustment Knob Ignition SwitchBrake Lever Hour MeterPre-Start Biodiesel Ready Operating InstructionsRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveDisengaging the PTO Engaging the PTOStopping the Engine Driving the Machine Adjusting the Cutting HeightAdjusting the Anti-Scalp Rollers Transporting a Unit TransportingLoading a Unit Recommended Maintenance Schedules MaintenanceCheck Engine Oil Level Check Battery ChargeService Interval As required Recommended Jump Starting ProcedureEngine Block of the Stalled Check Mower BladesCheck Rollover Protections Systems Roll Bar Pins Check Safety Interlock SystemService Air Cleaner Check Seat BeltCheck Hydraulic Oil Level Change Engine OilCheck Tire Pressures Lubricate Grease Fittings Check Condition Of BeltsLubricate Caster Wheel Hubs Wheel Hub Slotted Nut Torque SpecificationLubricate Brake Handle Pivot Lubricate Brake Rod BushingsDrain Fuel Filter/Water Separator Lubricate Motion Control Bronze BushingsChange Fuel Filter/Water Separator Change Inline Fuel FilterChange Engine Coolant Check Engine Coolant LevelThread Locking Adhesives Check Spark Arrester if equippedCopper-Based Anti-seize Mobil HTS Grease Or Food-Grade Anti-seizeDielectric Grease Deck LevelingPump Drive Belt Tension Mule Drive Belt Tension AdjustmentDeck Belt Tension Parking Brake Adjustment Belt Guide AdjustmentAlternator Belt Tension Lever down Remove pin to adjust Disengaged Removing the Shim Electric Clutch AdjustmentMotion Control Linkage Adjustment Reverse Indicator AdjustmentBecause of the jumper wire being used. Run Caster Pivot Bearings Pre-Load Adjustment Motion Control Damper AdjustmentClean Engine and Exhaust System Area Clean Engine Cooling SystemClean the Radiator Clean Grass Build-Up Under Deck Clean Debris From MachineBattery Disposal Waste DisposalProblem Possible Cause Corrective Action TroubleshootingTroubleshooting Troubleshooting Electrical Diagram SchematicsElectrical Schematic Exmark Commercial Turf Equipment Page Page Date Description of Work Done Service Done By Service RecordPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.