Exmark 000 & higher, 920 manual Reverse Indicator Adjustment, Motion Control Linkage Adjustment

Page 44

Maintenance

5. If adjustment is needed, loosen the nut against the yoke and while applying slight rearward pressure on the motion control lever, turn the head of the adjustment bolt in the appropriate direction until lever is centered (keeping rearward pressure on the lever will keep the pin at the end of the slot and allow the adjustment bolt to move the lever to the appropriate position). Tighten lock nut.

6. Repeat on opposite side of unit.

Figure 25

1. Feeler gauge

If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section.

If the gap is sufficient, proceed to the safety check in step F.

F.Perform the following safety check:

a.Sit on the seat and start the engine.

b.Make sure the blades Do Not engage with the PTO switch “off ” and the clutch disengaged.

If the clutch does not disengage, reinstall the shim and reference the Troubleshooting section.

c.Engage and disengage the PTO switch ten consecutive times to ensure the clutch is functioning properly. If the clutch does not engage properly, reference the Troubleshooting section.

Reverse Indicator

Adjustment

1.Stop engine, wait for all moving parts to stop, and remove key. Engage parking brake.

2.Unhook seat latch and tilt seat forward.

3.Begin with either the left or right motion control lever. Move lever to the neutral position and pull lever back until the clevis pin (on arm below pivot shaft) contacts the end of the slot (just beginning to put pressure on spring). (Figure 26).

4.Check where lever is relative to notch in console (should be centered allowing lever to pivot outward to the neutral lock position).

Figure 26

1.

Turn bolt here

4.

Yoke

2.

Lever centered in notch

5.

Loosen here

3.

End of slot

6.

Reverse indicator

 

 

 

 

Motion Control Linkage Adjustment

WARNING

Engine must be running and drive wheels must be turning so motion control adjustment can be performed. Contact with moving parts or hot surfaces may cause personal injury.

Keep fingers, hands, and clothing clear of rotating components and hot surfaces.

44

Image 44
Contents Lazer Z D-SERIES California Introduction Contents Safety Safety Alert SymbolSafe Operating Practices TrainingOperation Slope Operation Using the Rollover Protection System Rops Maintenance and StorageSafety Safety Safety and Instructional Decals 103-0223 103-0261 103-1798 103-2076 103-7218 107-2102 109-0872 109-1214 109-1215 109-1399 109-2219 109-2263 109-2264 109-2478 109-2951 109-3148 117-2718 19426-87881 19426-87903 107-9866 Systems SpecificationsModel Numbers Seat Hydrostatic Ground Drive SystemTires & Wheels Cutting DeckDimensions Torque RequirementsProduct Overview OperationControls Motion Control LeversIgnition Switch Tracking Adjustment KnobBrake Lever Hour MeterPre-Start Operating Instructions Biodiesel ReadyRaise the Rollover Protection System Rops Open the Fuel Shut-Off ValveStopping the Engine Engaging the PTODisengaging the PTO Adjusting the Cutting Height Driving the MachineAdjusting the Anti-Scalp Rollers Loading a Unit TransportingTransporting a Unit Maintenance Recommended Maintenance SchedulesCheck Battery Charge Check Engine Oil LevelRecommended Jump Starting Procedure Service Interval As requiredCheck Mower Blades Engine Block of the StalledCheck Safety Interlock System Check Rollover Protections Systems Roll Bar PinsService Air Cleaner Check Seat BeltCheck Tire Pressures Change Engine OilCheck Hydraulic Oil Level Check Condition Of Belts Lubricate Grease FittingsWheel Hub Slotted Nut Torque Specification Lubricate Caster Wheel HubsLubricate Brake Handle Pivot Lubricate Brake Rod BushingsLubricate Motion Control Bronze Bushings Drain Fuel Filter/Water SeparatorChange Fuel Filter/Water Separator Change Inline Fuel FilterCheck Engine Coolant Level Change Engine CoolantCheck Spark Arrester if equipped Thread Locking AdhesivesMobil HTS Grease Or Food-Grade Anti-seize Copper-Based Anti-seizeDielectric Grease Deck LevelingDeck Belt Tension Mule Drive Belt Tension AdjustmentPump Drive Belt Tension Alternator Belt Tension Belt Guide AdjustmentParking Brake Adjustment Lever down Remove pin to adjust Disengaged Electric Clutch Adjustment Removing the ShimReverse Indicator Adjustment Motion Control Linkage AdjustmentBecause of the jumper wire being used. Run Motion Control Damper Adjustment Caster Pivot Bearings Pre-Load AdjustmentClean the Radiator Clean Engine Cooling SystemClean Engine and Exhaust System Area Clean Debris From Machine Clean Grass Build-Up Under DeckBattery Disposal Waste DisposalTroubleshooting Problem Possible Cause Corrective ActionTroubleshooting Troubleshooting Schematics Electrical DiagramElectrical Schematic Exmark Commercial Turf Equipment Page Page Service Record Date Description of Work Done Service Done ByPage This page may be copied for personal use See EXMARK’S Complete Line of Accessories and Options
Related manuals
Manual 52 pages 57.34 Kb Manual 60 pages 43.2 Kb Manual 64 pages 37.72 Kb Manual 52 pages 8.82 Kb Manual 56 pages 15.39 Kb Manual 28 pages 32.2 Kb Manual 52 pages 61.7 Kb Manual 60 pages 62.85 Kb Manual 60 pages 23.73 Kb Manual 52 pages 50.76 Kb Manual 60 pages 57.72 Kb Manual 40 pages 46.04 Kb

920, 000 & higher specifications

The Exmark 920 is an exceptional piece of equipment tailored for professionals and enthusiasts alike. Designed with an emphasis on performance and reliability, this mower embodies the pinnacle of lawn care technology. Known for its robust construction, the Exmark 920 is equipped with a powerful engine, ensuring efficient and effective mowing even in demanding conditions.

One of the standout features of the Exmark 920 is its cutting deck. With a 52-inch or 60-inch mower deck option, it allows users to cover a large mowing area quickly. The deck is crafted from high-strength steel, providing durability and longevity while maintaining a lightweight design that enhances maneuverability. Innovative blade design promotes superior airflow for an even cut, preventing clumping and ensuring a polished finish across various grass types.

The Exmark 920 utilizes advanced technology, including the innovative RED Technology, which enhances engine performance by optimizing power consumption. This results in reduced fuel consumption while maintaining the required power output for demanding tasks. Additionally, the mower’s intuitive controls include a user-friendly interface, allowing for easy adjustments and settings, catering to the varying needs of different lawn types and conditions.

Another notable feature of the Exmark 920 is its all-day comfort design. With an ergonomic seat and advanced suspension system, operators can tackle long mowing sessions without discomfort. The padded seat is adjustable, providing maximum support to minimize fatigue, while the suspension system absorbs bumps and uneven terrain for a smoother ride.

Furthermore, the Exmark 920 prioritizes serviceability. Easy access points for maintenance and a well-designed layout ensure that routine tasks, such as oil changes and blade replacements, can be completed efficiently. The model also comes equipped with LED headlights for improved visibility during early morning or late evening mowing.

In summary, the Exmark 920 is a sophisticated mower combining power, advanced technology, and design for comfort and utility. Its high-performance engine, durable cutting deck, user-friendly controls, and serviceable layout make it an ideal choice for anyone seeking to achieve a well-manicured lawn with professional results. Whether for commercial or residential use, the Exmark 920 stands out as a leading option in the market, enabling users to tackle any mowing challenge with confidence and ease.