Exmark Lazer Z manual Operation Instructions, Controls, For locations and grease amounts

Page 20

3.8.8Route the long, unattached wiring harness lead up the left hand side of the handle and connect the two leads, in any order, to the operator presence control switch terminals on the inside of the control console. Fasten the lead to the handle with two large wire ties, from bolt bag, one at the upper end of the handle next to the console and one at the very lower end of the handle where it attaches to the fuel tank support.

3.9If the unit is shipped without the muffler attached, install with hardware provided.

3.10Service Engine: Follow the recommendations in the Engine Operators Manual.

3.11Grease unit.

NOTE: UNIT IS NOT GREASED AT THE FACTORY! Refer to Section

5.1.12for locations and grease amounts.

3.12Follow pre-start instructions as outlined in Section 4.2.

4.OPERATION INSTRUCTIONS

4.1CONTROLS

4.1.1Familiarize yourself with the controls and operation of the unit.

Carefully read the following information about the controls and their operation.

4.1.2Drive Levers:

Located on each side of the upper handle assembly directly below the handle grips. These levers individually control clutching action of the wheel drive belts and brakes. When the drive levers are all the way down, the wheel drive belts engage and the brakes disengage. Squeezing the left or right hand drive lever causes the left hand or right hand wheel to slow down or stop, which makes the machine turn to the left or right respectively. The sharpness of the turn varies by how much the lever is squeezed. If both levers are squeezed all the way back, both brakes will engage and the machine will stop. For straight ahead motion, smoothly release both drive levers to engage both drive wheels simultaneously.

4.1.3Neutral Lock/Parking Brake Latches:

Located directly above the drive levers. The purpose of these latches is to allow the operator to lock the drive levers in a "neutral" position where neither the wheel drive belts nor the brakes engage or in a “park brake” position where the wheel drive belts are not engaged and the park brake is engaged. To lock the drive levers in neutral, squeeze the drive levers back, place thumbs on the upper portion of the neutral lock/park brake latches and move them to the rear. Release drive levers. To lock the drive levers in “park brake” position, squeeze the drive levers back, place thumbs on the upper portion of the neutral lock/park brake latches and move them ahead. Release drive levers as stated in 4.1.2. (See Figure 12).

Apply parking brakes whenever leaving the operators position.

- 15 -

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Page R N in G Exmark Parts PLUS Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingOperation Give complete, undivided attention to the job at handPage Riding Attachments Maintenance and StorageSafety Signs KAWASAKI,KOHLER & 10.5 HP B&S Specifications Model NumberEngine Fuel SystemSafety Interlock System STEERING/BRAKE ControlTransmission Wheel Drive SystemTorque Requirements Assembly InstructionsDimensions Do not over tighten Upper Handle MountingUpper Handle Height Adjustment Kohler Speed Control Throttle Cable HOOK-UPKawasaki Speed Control Throttle Cable HOOK-UP 10.5 hp Speed Control Throttle Cable HOOK-UPFor B&S 8.5 hp Engines Nyloc nut See . Torque the 3/8 nut to 35 ft. lbs N⋅mLever and ROD Adjustment This Clearance should be Equal Shifter Lever To TransmissionNeutral Lock Lever Clearance Drive Lever Hardware LocationFor locations and grease amounts Operation InstructionsControls Drive LEVER, Neutral LOCK/PARK Brake Latch Operation Kawasaki,Kohler, and B&S 10.5 hp EnginesPRE-START 8.5 hp EnginesOperating Instructions Blade Engagement Transporting Maintenance and AdjustmentsPeriodic Maintenance Blade Bolt Installation Service Interval DailyCheck Brake and Wheel Drive Linkage Adjustment Service Interval 40 hrs Service Interval 160 hrsLubrication Chart Service Interval Refer to ChartFitting Initial Fitting Quantity Service Locations IntervalPivot Points Spray Lubricant ChartService Interval Adjustments Caster Height Adjustment Axle Height Adjustment Axle NO. of Spacers Number of 1/4 Blade Spacers Below SpindleCutter Deck Belt Adjustment Underneath engine deck Belt Guide LocationWheel drive spring tension adjustment Drive Belt Tension Adjustment PositionsTrouble Shooting Blades do not Stop When DisengagedMower Pulling Left or Right Mower Cuts UnevenlyEngine Troubleshooting Engine Troubleshooting TableMower Deck Belt Routing 36 Mower DeckWiring Diagrams Warranty Page Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care
Related manuals
Manual 44 pages 58.72 Kb

Lazer Z specifications

The Exmark Lazer Z is a premium zero-turn mower known for its exceptional performance, durability, and advanced features, making it a top choice for both homeowners and professional landscapers. With its innovative engineering and attention to detail, the Lazer Z series has earned a strong reputation in the lawn care industry.

One of the primary features of the Exmark Lazer Z is its powerful engine options. Customers can choose from a variety of engines, including reliable Kohler and Kawasaki models, ensuring that every user can find the perfect fit for their mowing needs. These engines offer impressive horsepower, enabling the Lazer Z to handle even the toughest mowing conditions with ease.

The Lazer Z's cutting deck is another standout feature. Available in several sizes, typically ranging from 48 to 72 inches, the Aerodynamic design of the UltraCut cutting deck allows for efficient grass flow, providing a clean and even cut. The deck is made from durable materials, ensuring longevity and resistance to wear and tear. Furthermore, the deck height can be easily adjusted, giving users the flexibility to achieve their desired grass length.

The patented Red Technology is integrated into the Lazer Z, providing advanced features like the Smart Control, which optimizes performance in real time. This technology enhances fuel efficiency and reduces overall operating costs, making it an eco-friendly choice in a competitive market. Alongside this, the Lazer Z is designed with a responsive and intuitive control system that allows for precise maneuvering, making it easier to navigate tight spaces and complex landscapes.

Comfort is also at the forefront of the Lazer Z's design. Its ergonomically designed seat, equipped with high back support and adjustable armrests, ensures that operators remain comfortable during long mowing sessions. The Lap Bar control system offers smooth and effortless steering, enhancing user experience and reducing fatigue.

In terms of maintenance, the Exmark Lazer Z is designed to facilitate easy access to critical components. This allows for quick maintenance and service, ensuring that the mower remains in peak condition over its lifespan. Additionally, with a durable frame and robust construction, the Lazer Z is built to withstand the rigors of daily use.

Overall, the Exmark Lazer Z combines power, precision, and comfort, making it a preferred choice for anyone looking to achieve professional-quality results on their lawn. Whether for residential or commercial use, the Lazer Z delivers unmatched performance to meet a variety of mowing needs.
Top Page Image Contents