Exmark Lazer Z manual Adjustments

Page 31

5.1.19An anti-seize compound is used on the blade drive pulley hub, located on the engine PTO shaft (this allows for ease of removal of the pulley).

5.1.20Dielectric grease is used on all blade type electrical connections to prevent corrosion and loss of contact.

5.2ADJUSTMENTS

5.2.1Adjusting cutting height with blade spacers.

Blades may be adjusted for cutting height by using the four 1/4" spacers found on the blade spindle bolts (factory setting is two above and two below). This allows a 1" range in 1/4" increments of cutting height in any axle position. The same number of blade spacers must be used on all blades to achieve a level cut (two above and two below, one above and three below, etc.).

For the best cut and discharge, place a minimum of two spacers between the blade and spindle shaft.

For the highest quality cut, place all four spacers between the blade and the spindle shaft.

If the mulching kit is installed, the highest quality cut can be obtained with 3 spacers between the blade and spindle (minimum is 1 for a good cut).

If you need to cut higher or lower than what the spacers will allow, it will be necessary to adjust the rear axle height and caster position. See Section 5.2.2 below.

5.2.2Axle height and caster position.

Desired cutting height range can be obtained by adjusting the rear axle and placing caster spacers above or below the caster arm (See Figures 14 and 15). It may be necessary to readjust wheel drive and brake linkages.

To adjust rear axle:

a)Stop engine and remove spark plug wire(s).

b)Place the drive levers in the neutral lock position.

c)Remove mower deck belt shield for access to axle adjustment belts.

d)Loosen but do not remove the two (2) axle pivot bolts and the two (2) axle adjustment bolts (See Figure 15).

e)Place a jack under the rear center of the engine deck.

f)Raise the back end of the engine deck up enough to remove the two (2) axle adjustment bolts.

g)With the jack, raise or lower the back end of the engine deck so that two (2) axle adjustment bolts can be reinstalled in desired hole location. A tapered punch can be used to help align the holes.

h)Retighten all four (4) bolts, lower unit and remove jack.

i)Install mower deck belt shield.

j)Adjust wheel drive and brake linkages as required. (See Sections 3.8.5 and 3.8.6).

k)Using the appropriate chart for your unit, adjust the caster spacers as directed to match with the axle hole selected. (See Figure 15)

- 26 -

Image 31
Contents Page R N in G Exmark Parts PLUS Program Operators Manual Table of Contents Training SafetyYour Safety is Involved Safety Alert SymbolGive complete, undivided attention to the job at hand OperationPage Safety Signs Maintenance and StorageRiding Attachments KAWASAKI,KOHLER & 10.5 HP B&S Fuel System SpecificationsModel Number EngineWheel Drive System Safety Interlock SystemSTEERING/BRAKE Control TransmissionDimensions Assembly InstructionsTorque Requirements Upper Handle Mounting Do not over tightenKohler Speed Control Throttle Cable HOOK-UP Upper Handle Height Adjustment10.5 hp Speed Control Throttle Cable HOOK-UP Kawasaki Speed Control Throttle Cable HOOK-UPNyloc nut See . Torque the 3/8 nut to 35 ft. lbs N⋅m For B&S 8.5 hp EnginesThis Clearance should be Equal Shifter Lever To Transmission Lever and ROD AdjustmentDrive Lever Hardware Location Neutral Lock Lever ClearanceControls Operation InstructionsFor locations and grease amounts Kawasaki,Kohler, and B&S 10.5 hp Engines Drive LEVER, Neutral LOCK/PARK Brake Latch Operation8.5 hp Engines PRE-STARTOperating Instructions Blade Engagement Periodic Maintenance Maintenance and AdjustmentsTransporting Service Interval Daily Blade Bolt InstallationCheck Brake and Wheel Drive Linkage Adjustment Service Interval 160 hrs Service Interval 40 hrsInterval Lubrication ChartService Interval Refer to Chart Fitting Initial Fitting Quantity Service LocationsService Interval Spray Lubricant ChartPivot Points Adjustments Caster Height Adjustment Axle Height Adjustment Below Spindle Axle NO. of Spacers Number of 1/4 Blade SpacersCutter Deck Belt Adjustment Belt Guide Location Underneath engine deckDrive Belt Tension Adjustment Positions Wheel drive spring tension adjustmentMower Cuts Unevenly Trouble ShootingBlades do not Stop When Disengaged Mower Pulling Left or Right36 Mower Deck Engine TroubleshootingEngine Troubleshooting Table Mower Deck Belt RoutingWiring Diagrams Warranty Page Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care
Related manuals
Manual 44 pages 58.72 Kb

Lazer Z specifications

The Exmark Lazer Z is a premium zero-turn mower known for its exceptional performance, durability, and advanced features, making it a top choice for both homeowners and professional landscapers. With its innovative engineering and attention to detail, the Lazer Z series has earned a strong reputation in the lawn care industry.

One of the primary features of the Exmark Lazer Z is its powerful engine options. Customers can choose from a variety of engines, including reliable Kohler and Kawasaki models, ensuring that every user can find the perfect fit for their mowing needs. These engines offer impressive horsepower, enabling the Lazer Z to handle even the toughest mowing conditions with ease.

The Lazer Z's cutting deck is another standout feature. Available in several sizes, typically ranging from 48 to 72 inches, the Aerodynamic design of the UltraCut cutting deck allows for efficient grass flow, providing a clean and even cut. The deck is made from durable materials, ensuring longevity and resistance to wear and tear. Furthermore, the deck height can be easily adjusted, giving users the flexibility to achieve their desired grass length.

The patented Red Technology is integrated into the Lazer Z, providing advanced features like the Smart Control, which optimizes performance in real time. This technology enhances fuel efficiency and reduces overall operating costs, making it an eco-friendly choice in a competitive market. Alongside this, the Lazer Z is designed with a responsive and intuitive control system that allows for precise maneuvering, making it easier to navigate tight spaces and complex landscapes.

Comfort is also at the forefront of the Lazer Z's design. Its ergonomically designed seat, equipped with high back support and adjustable armrests, ensures that operators remain comfortable during long mowing sessions. The Lap Bar control system offers smooth and effortless steering, enhancing user experience and reducing fatigue.

In terms of maintenance, the Exmark Lazer Z is designed to facilitate easy access to critical components. This allows for quick maintenance and service, ensuring that the mower remains in peak condition over its lifespan. Additionally, with a durable frame and robust construction, the Lazer Z is built to withstand the rigors of daily use.

Overall, the Exmark Lazer Z combines power, precision, and comfort, making it a preferred choice for anyone looking to achieve professional-quality results on their lawn. Whether for residential or commercial use, the Lazer Z delivers unmatched performance to meet a variety of mowing needs.