Exmark Lazer Z manual Service Interval 40 hrs, Service Interval 160 hrs

Page 28

engines). Clean around oil filter and unscrew filter to remove. Before the new filter is installed, apply a thin coating of oil on the surface of the rubber seal. Turn filter clockwise until rubber seal contacts the filter adapter, then tighten filter an additional 2/3 to 3/4 turn.

f)Clean around oil fill cap and remove. Fill to specified capacity and replace cap. Refer to Engine Owner's Manual for correct oil level and the SAE Grade recommended by the manufacturer.

Do Not overfill.

g)Start the engine and check for leaks. Stop engine and recheck oil levels.

5.1.9Check tire pressures.

Service Interval: 40 hrs.

a)Stop engine and remove spark plug wire(s). Check air pressure in tires; recommended tire pressure is: rear, 12 to 16 psi; pneumatic casters, 22 psi.

b)Inflate tires to pressures stated above. Measure circumference of each drive tire. Adjust tire pressures within the above range to try to make tire circumferences match as closely as possible.

Note: Front caster tires have permanent tire sealant installed.

5.1.10Check grease level, input and output shaft bearing wear on Peerless Transmission. (Replace gearbox grease yearly)

Service Interval: 160 hrs.

a)Stop engine and remove spark plug wire(s).

b)Place drive levers and neutral lock/park brake latches in the neutral lock position.

c)Remove shifter lever from top of transmission.

d)Remove shifter plate from top of transmission and the two leads from the neutral start switch.

e)Release the tension on the transmission belt.

f)Check for side play caused by bearing wear on the input and output shafts of the transmission. Replace bearings if necessary.

g)Remove the six bolts that fasten the upper case to the lower case and carefully remove the upper case half.

h)Check the grease level in the lower case. The grease level should be approximately 1-1/2" to 1-3/4" from the gearbox bottom. If necessary, fill to proper level with Peerless grease (Part No. 788067).

I)Reinstall upper case half and fasten in place with six bolts previously removed.

j)Reinstall all parts removed in Steps c and d. Install drive belt and adjust tension as stated in Section 5.2.3.

- 23 -

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Page R N in G Exmark Parts PLUS Program Operators Manual Table of Contents Safety Your Safety is InvolvedSafety Alert Symbol TrainingOperation Give complete, undivided attention to the job at handPage Safety Signs Maintenance and StorageRiding Attachments KAWASAKI,KOHLER & 10.5 HP B&S Specifications Model NumberEngine Fuel SystemSafety Interlock System STEERING/BRAKE ControlTransmission Wheel Drive SystemDimensions Assembly InstructionsTorque Requirements Do not over tighten Upper Handle MountingUpper Handle Height Adjustment Kohler Speed Control Throttle Cable HOOK-UPKawasaki Speed Control Throttle Cable HOOK-UP 10.5 hp Speed Control Throttle Cable HOOK-UPFor B&S 8.5 hp Engines Nyloc nut See . Torque the 3/8 nut to 35 ft. lbs N⋅mLever and ROD Adjustment This Clearance should be Equal Shifter Lever To TransmissionNeutral Lock Lever Clearance Drive Lever Hardware LocationControls Operation InstructionsFor locations and grease amounts Drive LEVER, Neutral LOCK/PARK Brake Latch Operation Kawasaki,Kohler, and B&S 10.5 hp EnginesPRE-START 8.5 hp EnginesOperating Instructions Blade Engagement Periodic Maintenance Maintenance and AdjustmentsTransporting Blade Bolt Installation Service Interval DailyCheck Brake and Wheel Drive Linkage Adjustment Service Interval 40 hrs Service Interval 160 hrsLubrication Chart Service Interval Refer to ChartFitting Initial Fitting Quantity Service Locations IntervalService Interval Spray Lubricant ChartPivot Points Adjustments Caster Height Adjustment Axle Height Adjustment Axle NO. of Spacers Number of 1/4 Blade Spacers Below SpindleCutter Deck Belt Adjustment Underneath engine deck Belt Guide LocationWheel drive spring tension adjustment Drive Belt Tension Adjustment PositionsTrouble Shooting Blades do not Stop When DisengagedMower Pulling Left or Right Mower Cuts UnevenlyEngine Troubleshooting Engine Troubleshooting TableMower Deck Belt Routing 36 Mower DeckWiring Diagrams Warranty Page Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Products for Turf Care
Related manuals
Manual 44 pages 58.72 Kb

Lazer Z specifications

The Exmark Lazer Z is a premium zero-turn mower known for its exceptional performance, durability, and advanced features, making it a top choice for both homeowners and professional landscapers. With its innovative engineering and attention to detail, the Lazer Z series has earned a strong reputation in the lawn care industry.

One of the primary features of the Exmark Lazer Z is its powerful engine options. Customers can choose from a variety of engines, including reliable Kohler and Kawasaki models, ensuring that every user can find the perfect fit for their mowing needs. These engines offer impressive horsepower, enabling the Lazer Z to handle even the toughest mowing conditions with ease.

The Lazer Z's cutting deck is another standout feature. Available in several sizes, typically ranging from 48 to 72 inches, the Aerodynamic design of the UltraCut cutting deck allows for efficient grass flow, providing a clean and even cut. The deck is made from durable materials, ensuring longevity and resistance to wear and tear. Furthermore, the deck height can be easily adjusted, giving users the flexibility to achieve their desired grass length.

The patented Red Technology is integrated into the Lazer Z, providing advanced features like the Smart Control, which optimizes performance in real time. This technology enhances fuel efficiency and reduces overall operating costs, making it an eco-friendly choice in a competitive market. Alongside this, the Lazer Z is designed with a responsive and intuitive control system that allows for precise maneuvering, making it easier to navigate tight spaces and complex landscapes.

Comfort is also at the forefront of the Lazer Z's design. Its ergonomically designed seat, equipped with high back support and adjustable armrests, ensures that operators remain comfortable during long mowing sessions. The Lap Bar control system offers smooth and effortless steering, enhancing user experience and reducing fatigue.

In terms of maintenance, the Exmark Lazer Z is designed to facilitate easy access to critical components. This allows for quick maintenance and service, ensuring that the mower remains in peak condition over its lifespan. Additionally, with a durable frame and robust construction, the Lazer Z is built to withstand the rigors of daily use.

Overall, the Exmark Lazer Z combines power, precision, and comfort, making it a preferred choice for anyone looking to achieve professional-quality results on their lawn. Whether for residential or commercial use, the Lazer Z delivers unmatched performance to meet a variety of mowing needs.
Top Page Image Contents