Exmark Lazer HP manual Waste Disposal, Motor OIL Disposal, Engine Coolant Disposal

Page 50

6. WASTE DISPOSAL

6.1 MOTOR OIL DISPOSAL

Engine oil and hydraulic oil are both pollutants to the environment. Dispose of used oil at a certified recycling center or according to your state and local regulations.

6.2 ENGINE COOLANT DISPOSAL

CAUTION

POTENTIAL HAZARD

Engine coolant is toxic.

WHAT CAN HAPPEN

Swallowing coolant can cause poisoning.

HOW TO AVOID THE HAZARD

Do not swallow

Keep out of reach of children and pets.

Dex-Cool© contains ethylene glycol. Ethylene glycol is a pollutant. Dispose of used engine coolant according to your state and local regulations.

6.3 MERCURY SWITCH DISPOSAL

CAUTION

POTENTIAL HAZARD

The mercury contained in the tilt switch is poisonous.

WHAT CAN HAPPEN

Exposure to mercury can cause severe illness.

HOW TO AVOID THE HAZARD

Never attempt to open or repair the tilt switch

Avoid contact with the mercury.

The tilt switch (PN 1-633782) on this unit contains mercury, a hazardous material. Mercury that is outside a sealed container vaporizes at room temperature. The vapors are harmful. Mercury can be absorbed through the skin. Do not attempt to open or repair this switch.

A very small amount of mercury is contained in a hermetically sealed body. The steel switch is then potted in a hard epoxy in a plastic case. It is unlikely that the mercury will ever escape from the enclosure. These high performance and reliable inexpensive switches are recyclable. Mercury is an important and beneficial compound but requires special care in handling and disposal. When used and managed properly, mercury is not a threat to people or the environment. This information is presented to users so that they are aware that these switches contain mercury and will apply sound disposal practices when these devices reach their normal end of life or are damaged.

Several states have passed laws concerning the disposal of devices containing mercury. In all the remaining states it is advisable to follow similar procedures. The laws state that these sealed devices contain mercury and should not be placed in the garbage until the mercury is removed and reused, recycled or otherwise managed to insure that it does not become part of solid waste or waters. Management and disposal practices must be within relevant federal, state, or local laws.

Return the switch to your Exmark dealer if it is faulty and is being replaced or if the unit containing the switch is no longer operating and is being scrapped. If the switch is damaged or broken open use extreme caution in handling. Call your local waste management authority or Exmark Customer Service for instructions.

- 45 -

Image 50
Contents For Serial Nos 440,000 & Higher Potential Hazard Exmark Parts PLUS Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Safe Zone for Mowing There is no rollover protection when the roll bar is down Maintenance and Storage For Kawasaki Liquid-Cooled units Safety Signs Page Location RH Side on Top Specifications Cutting Deck Hydrostatic Ground Drive SystemTires Dimensions Torque RequirementsAssembly Instructions Uncrate Mower Install Rollover Protection System Roll BARLower Roll BAR Installation Machine is shipped with a filled lead acid battery Service BatteryUpper Roll BAR Installation Check Tire Pressure Install Drive WheelsInstall Motion Control Levers Service Engine Service Engine Coolant Position Discharge ChuteControls Service Hydraulic OILOperation Instructions Motion Control PositionsPotential Hazard Push the lever forward and down to disengage the brake PRE-START Operating InstructionsTransporting Do not drive a unit on a public street or roadway Service Interval Daily Maintenance & AdjustmentsPeriodic Maintenance Service Interval Monthly Service Interval Daily or more often in dry conditions Blade Bolt Installation Service Interval Daily Service Interval 50 hours Service Interval 100 hrsCoolant Plug Location Service Interval 40 hr Service Interval 40 hrsLubrication Chart Service Interval Refer to chartService Interval 160 hrs Service Interval Once YearlyCaster Wheel Assembly Service Interval As Required Service Interval After First 250 hrs Then yearly thereafterAdjustments Service Interval 500 hrsANTI-SCALP Roller Adjustment Cutting Height PositionSwivel Adjustment Spring Compression Adjustment Self-tensioning No adjustment necessaryMule Drive Belt Adjustment Brake Adjustment Belt Guide PositioningThrottle Tension No adjustment necessaryReverse Indicator Adjustment Motion Control Adjustment Caster Adjustment Armrest AdjustmentMotor OIL Disposal Mercury Switch DisposalWaste Disposal Engine Coolant DisposalMower Pulls Left or Right W/LEVERS Fully Forward Trouble ShootingBattery Disposal Mower Cuts UnevenlyEngine Warning Systems Engine Troubleshooting TableProblem Electrical Diagram Hydraulic Diagram Limited Warranty Exmark Turf Equipment Page Page Service Record Page See EXMARK’S Complete Line of Products for Turf Care