Exmark Lazer Z CT manual Pre-Start, Mowing

Page 22

Rotate the valve 1/4 turn clockwise to shut off fuel. Rotate the valve 1/4 turn counter-clockwise to turn on fuel.

3.1.11Fuel Gauge: Located on the left fuel tank. The fuel gauge monitors the amount of fuel in the tank.

3.1.12Drive Wheel Release Valves: Located on the right front corner of the hydrostatic pumps. Drive wheel release valves are used to release the hydrostatic drive system to allow the machine to be pushed without the engine running. Unhook seat latch and tilt seat up to gain access to pumps.

With a 5/8 wrench, turn both valves one turn counter-clockwise to release drive system.

Turn clockwise to reset system. DO NOT overtighten. DO NOT tow machine.

3.2PRE-START

3.2.1Fill fuel tank. For best results use only clean, fresh regular grade unleaded gasoline with an octane rating of 87 or higher. Regular grade leaded gasoline may also be used; however, combustion chamber and cylinder head will require more frequent service. See Engine Owner's Manual. DO NOT add oil to gasoline.

Do Not overfill fuel tank. Never fill the fuel tank so that the fuel level rises above a level that is 1/2” below the bottom of the filler neck to allow for fuel expansion and prevent fuel spillage.

3.2.2Make sure you understand the controls, their locations, their functions, and their safety requirements.

3.2.3Refer to Maintenance, Section 4, and perform all the necessary inspection and maintenance steps.

3.3MOWING

3.3.1Operate units with the roll bar in the raised and locked position and use seat belt. There is no rollover protection when the roll bar is down. If it is necessary to lower roll bar do not wear the seat belt. Raise the roll bar as soon as clearance permits.

3.3.2Open fuel shut-off valve.

The fuel shut-off valve is located under the seat in the fuel line between the left fuel tank and the engine.

3.3.3Starting Engine:

Brake must be engaged, the PTO switch disengaged, and the motion control levers out (neutral lock position). (The operator does not need to be in the seat to start the engine.)

On a cold engine, place the throttle midway between the “SLOW” and “FAST” positions and place the choke to the “ON” position. Turn ignition switch to the “start” position. Release the switch as soon as the engine starts.

IMPORTANT: DO NOT crank the engine continuously for more than ten (10) seconds at a time. If the engine does not start, allow a 60 second cool-down period between starting attempts. Failure to follow these guidelines can burn out the starter motor.

After starting a cold engine, gradually return choke to the “OFF” position as the engine warms up.

On a warm engine, place the throttle midway between the “SLOW” and “FAST” positions and leave the choke in the “OFF” position.

17

Page 21 Page 23
Image 22
Page 21 Page 23
Contents For Serial Nos 670,000 & Higher Potential Hazard Exmark Parts PLUS→ Program Operators Manual Table of Contents Safety Alert Symbol SafetyYour Safety is Involved TrainingCarbon monoxide can kill you Potential Hazard Operation Potential Hazard There is no rollover protection when the roll bar is down Page Maintenance and Storage Safety Signs Page Page Specifications Tires and Wheels Hydrostatic Ground Drive SystemCutting Deck Torque Requirements DimensionsOperation Instructions ControlsPotential Hazard Push the lever forward and down to disengage the brake PRE-START MowingEngaging PTO Transporting Potential Hazard Periodic Maintenance Maintenance & AdjustmentsService Interval Daily Service Interval Daily or more often in dry conditions Service Interval MonthlyService Interval Daily Check safety interlock system Service Interval 40 hr Service Interval 40 hrs Lubrication ChartService Interval Refer to chart Service Interval Once Yearly Service Interval 160 hrsService Interval As Required Service Interval 80 hrsService Interval After First 250 hrs Then yearly thereafter Service Interval After First 100 hrs Then 500 hrs thereafter Adjustments Page Self-tensioning No adjustment necessary No adjustment necessary Reverse Turn Bolt Indicator Here END Slot Page Trouble Shooting Waste DisposalEngine Troubleshooting Table ProblemBriggs & Stratton Electrical Diagram Hydraulic Diagram Year Limited Warranty Service Record Fold Along Appropriate Line See EXMARK’S Complete Line of Accessories

Lazer Z CT specifications

The Exmark Lazer Z CT is a standout zero-turn mower designed for both residential and commercial landscaping professionals who demand efficiency, durability, and cutting precision. This powerful mower has redefined the standards for productivity in the turf care industry, making it a popular choice among operators who handle regular and extensive mowing tasks.

One of the main features of the Lazer Z CT is its robust cutting system, which is built to deliver an exceptional quality of cut. The mower is equipped with Exmark's patented Optimized Cutting System, which includes advanced engine and deck designs that work together to deliver superior performance. With deck options ranging from 48 to 60 inches, the Lazer Z CT caters to a variety of mowing needs, allowing operators to choose the right size for their landscape.

The Lazer Z CT is powered by a range of high-performance engines, including the reliable Kohler and Kawasaki offerings. These engines are engineered for maximum torque and power, ensuring that the mower can handle tough mowing conditions with ease. The advanced cooling systems also help to prolong engine life and reduce downtime, making this mower a dependable workhorse.

In terms of technology, the Lazer Z CT features a user-friendly control system that enhances maneuverability and comfort. The intuitive control levers allow for precise handling, especially in tight spaces and around obstacles. Additionally, the padded seat and ergonomic design ensure that operators can work for extended periods without discomfort.

Another notable characteristic of the Lazer Z CT is its exceptional build quality. Constructed with heavy-duty materials, the mower is engineered to withstand the rigors of daily use. Features such as the durable steel frame and commercial-grade transmission add to its longevity, making it a sound investment for lawn care professionals.

Furthermore, the mower's maintenance-friendly design simplifies routine upkeep tasks. Features like the accessible oil filter and easy-to-reach greasing points make it convenient for operators to perform regular maintenance, ensuring the mower remains in peak condition.

In conclusion, the Exmark Lazer Z CT combines power, precision, and comfort in a zero-turn mower that meets the demands of both residential and commercial applications. With its innovative technologies and robust features, it is an excellent choice for anyone looking to enhance their mowing efficiency and quality.
Top Page Image Contents